Sunrise Medical Quickie Q50R Скачать руководство пользователя

Страница: 26 / 32

Q50R REV.A

7.0 Trouble shooting

Phenomenon

Possible Causes

Solution

Number of

replacemen

t parts

Method

obtaining

Short

driving

distance

A: Battery charging time

is short

B: The battery is aging

and the energy storage

is insufficient

A: Charge the battery overnight

or ensure it is charged for 8

hours.

B: Replace the battery.

A:/

Batteryx1

Contact an

authorized

reseller

Intco

purchase

Battery can not

be charged

The

charger

damaged

B: The battery line is

loose; or the battery

fuse is damaged

Charging

power

outlet is dead

D: Charger, charger

wire,

plug,

bad

internal wiring

Replace

the

charger.

B: Check all the wiring, connect

the wiring; or replace the fuse.

C: Replace with a new power

outlet.

D: It may be necessary to

replace

the

charger

and

internal overhaul.

A: charger

B:/

C:/

D: charger

Contact an

authorized

reseller

Intco

purchase

Battery

charging

current is too

large

The battery is damaged

Check the battery for a short

circuit. Replace the battery if

necessary.

Batteryx1

Contact an

authorized

reseller

Intco

purchase

The

charge

indicator

will

soon show a

low

battery

charge

after

charging

A: The battery is aging

and the charge cannot

be saved

B: circuit failure

C: charger failure

A: Replace the battery.

Please

contact

the

dealer/manufacturer.

C: Replace the charger, please

contact

the

dealer/manufacturer

：

Batteryx1

：

Charger

Contact an

authorized

reseller

Intco

purchase

The

battery

indicator

flashes

immediately

after

recharging,

showing

low

battery

A: Battery aging

B: circuit failure

C: charger failure

A: Replace the battery.

Please

contact

the

dealer/manufacturer.

C: Replace the charger

：

Batteryx1

：

Charger

Contact an

authorized

reseller

Intco

purchase

Wheelchairs

A: power wheelchair in A: Turn the motor wrench to the A

：

Contact an

Содержание Quickie Q50R

































Результаты поиска

Содержание Quickie Q50R

Отзывы:

Похожие инструкции для Quickie Q50R

Бренды по названию

Популярные бренды

Sunrise Medical Quickie Q50R, Инструкция по эксплуатации

Результаты поиска

Содержание Quickie Q50R

Отзывы:

Похожие инструкции для Quickie Q50R

Бренды по названию

Популярные бренды