Function introduction
Important:
Read All Instructions Prior to Installation
Safety & Warnings
•
This device contains a button lithium battery that shall be stored and disposed properly.
•
DO NOT expose the device to moisture.
Quick Start
How to install:
•
Step 1: turn on your remote control.
•
Step 2: activate inclusion mode on your Z-Wave controller.
•
Step 3: activate inclusion mode of your remote control by pressing and holding down both buttons All on
and All off for over 3 seconds.
Product Description
The remote control is a Z-Wave device that can both control other Z-Wave devices and activate scenes in
Gateways. Although it is controlling other devices, the device cannot act as Z-Wave network controller (primary
or secondary) and will always need a Z-Wave network controller to be included into a Z-Wave network. It also
supports the Over The Air (OTA) feature for the product’s firmware upgrade.
The remote control has following functions:
1. Control of groups of other Z-Wave devices using 'ON', 'OFF' and Dim commands.
2. Activation of scenes in Gateway mode.
The encryption modes that the remote control supports are S0, S2 Authenticated, S2 Unauthenticated. When
the remote control is being included into a Z-Wave network, you can use your primary controller/gateway to
enable one encryption mode or disable encryption. (The primary controller/gateway shall support encryption
mode configuration).
09.ZV9001K12Z4.04772
Installation Guide
Please read carefully the enclosed user manual before installation of remote control, in order to ensure an
error-free functioning.
The remote control unit supplied as complete set for flush mounting in the standard circular European wall
boxes with 60mm diameter.
Inclusion (Adding to a Z-Wave network)
Step 1. Make sure the remote control does not belong to any Z-Wave network, short press any button, if LED
indicator does not turn on, the remote control does not belong to any network, then continue step 2,if LED
indicator turns on, it means the remote control has already been included to a network, please first set the
remote control to exclusion mode (refer to the part "Exclusion" of this manual),then continue step 2.
Step 2. Set primary controller/gateway into inclusion mode (Please refer to your primary controllers manual on
how to turn your controller into inclusion).
Step 3. Press and hold down both buttons All On and All Off for over 3 seconds, LED indicator turns on, the
remote control will be set to inclusion mode, and waiting to be included, after 10s LED indicator blinks 6 times
quickly to indicate successful inclusion. The remote control is a sleepy device, after inclusion it will not enter
into sleepy mode immediately, and will continue activation status for 30s and wait data interaction from the
gateway, the LED indicator will stay solid on, please be patient to wait LED indicator to turn off.
Exclusion (Removing from a Z-Wave network)
There are two exclusion methods:
Method 1: Exclusion from the primary controller/gateway as follows:
1. Set the primary controller/gateway into exclusion mode (Please refer to your primary controllers manual on
how to set your controller into exclusion).
2. Press and hold down both buttons All On and All Off for over 3 seconds, LED indicator turns on, the
remote control will be set to exclusion mode, and waiting to be excluded, after 7s LED indicator blinks 4 times
quickly to indicate successful exclusion.
Z-Wave Dim Remote Control
Note:Before the first use, please remove the protective film on the batteries.
Front side
Back side
Click to turn ON all groups
Press and hold down to save colors/scenes;
Click to recall the saved colors/scenes
Click to turn OFF all groups
Group 2: Click to turn ON, press and hold
down to increase light intensity
Group
down to decrease light intensity
2: Click to turn OFF, press and hold
Group 3
Group 3
Group 4
Group 4
Group 5
Group 5
LED indicator
Press and hold down both keys together for
3s to be added to or removed from z-wave
network by a Master (Primary) controller.
Product Data
Z-Wave Frequency
Power Supply
Operating temperature
Relative humidity
Dimensions
Waterproof Grade
868.42MHz(EU)/908.42MHz(US)/921.42MHz(ANZ)
6VDC(2xCR2450 battery)
0 to 40°C
8% to 80%
150x40x13.6mm
IP20
