6454L/ISS2
1
1
1
3
1
5
2
5
4
8
3
6
2
7
3
8 3
2
5
5
4
Tools required
Fitting Instructions
Please keep for future reference
6139L/ISS1
Should any component be missing, please call the Customer Care Department on
0330 005 2233.
Pack Content
Please read these instructions carefully and check the contents of the pack before attempting to
assemble and fi x this product.
Safety Recommendation
Only use a Step Ladder to install this product.
DO NOT over reach. Always move the Step Ladder so that you are in a safe working position.
DO NOT hold or lean on the pole to support your weight.
We recommend you use two people for installation of larger poles.
Take care when using power tools, use of a Residual Current Device (RCD) is recommended.
Always use eye protection when drilling. Beware of hidden pipe runs and cables.
No liability will be accepted for damage or injury caused by incorrectly installed or assembled product.
PLEASE KEEP OUT OF THE REACH OF YOUNG CHILDREN. SMALL PARTS - CHOKING HAZARD
PLEASE KEEP THESE INSTRUCTIONS AND THE BATCH CODE ON THE PACKAGING FOR FUTURE
REFERENCE IN CASE OF ANY QUERIES
SWISH DESIGN STUDIO BAY KIT
Bay Length
Parts
300cm
400cm
500cm
1
Pole
4
4
4
2
Bracket
3
3
2
3
Pass Over Bracket
4
4
4
4
Standard Collar
2
2
2
5
Solid Ring
4
4
4
6
Pass Over Ring
26
36
46
7
Joiner
1
1
1
8
Bay Corner
2
2
2
3
6
5
2
3
1
3
2
4
1
3
2
6
6
1
5
stud drawing.AI 3 01/04/2014 09:19:22
OR
3
6
5
2
3
1
3
2
4
1
3
2
6
6
1
5
7
{
SWISH ELEMENTS BAY KIT
Bay Length
400cm
1 Corner Joint
2
2 End Brackets
3
3 Passing Brackets
4
4 Pass Over Rings
36
5 Solid Rings
4
6 Pole
3
7 Finial
2
Sunfl ex, Keys Park Road, Hednesford, Cannock, WS12 2FR
• tel: +44 (0)330 005 2233 • fax: +44(0) 1543 279505
• email: enquiries@sunfl ex.co.uk • web: www.sunfl ex.co.uk
17
Distance between bracket centers
d1
Distance between bracket centers
Length of end pole = d1 +
147.5mm
90°
135°
180°
16
2.95
19
2.95
2.95
d1+d2+d1=Pole Length
Approx.
10cm
d2 (distance between end brackets)
Approx.
10cm
d1
d1
24
23
2.95
2.95
2.95
2.95
18
20
22
21
Distance between bracket centers
d1
Distance between bracket centers
Length of end pole = d1 +
147.5mm
90°
135°
180°
15
Sunfl ex , Keys Park Road, Hednesford, Cannock, WS12 2FR
• tel: +44 (0)330 005 2233 • fax: +44(0) 1543 279505
• email: enquiries@sunfl ex.co.uk • web: www.sunfl ex.co.uk
Preparing the curtain
(fi g.17)
1. Leave the solid rings aside, slide the pass over rings and 1
solid rings onto the pole, approximately 1 ring per 100mm of
pole, ensuring that 1 solid ring goes on last.
2. When using a centre bracket an equal number of rings will
need to be used either side of the bracket.
Fitting the Bay Corner
1. Adjust the bay corner into the desired angle by loosening the
segment screws. Once in the desired positon re-secure the
screws. (fi g.15)
2. Slide the poles onto the plastic bung ends of the bay corners.
(fi g.16)
Bay corners should always be supported by two pass over
brackets.
Fixing the collar
(fi g.19)
1. Position one solid ring between the bracket and the collar.
2. Push the collar onto the end of the pole.
3. Tighten the grub screw on the collar.
Fixing the fi nial
1. If the collar is already installed on the pole, unscrew the grub
screw and remove the collar. We do not recommend installing
the fi nial while the collar is fi tted as it could scratch the pole.
(fi g.20)
2. Screw the fi nial on the cup end of the collar. Please note that
different design are available through the range. (fi g.21)
3. Push the fi nial onto the end of the pole. (fi g.22)
4. Tighten the grub screw on the collar.
Installing the curtain
1. Equally space curtain hooks along curtain header, you will
require one hook for every ring. (fi g.23)
2. Place hooks through the eyelet on the ring. (fi g.23)
3. Test the installation by drawing the curtains across the pole.
(fi g.24)
Fixing the pole
(fi g. 18)
1. Loosen the grub screw on the bracket.
2. Place pole in bracket.
3. Tighten the grub screw until the pole does not slide in the
bracket.
Fitting the Bay Corner
1. Adjust the bay corner into the desired angle by loosening the
segment screw. Once in the desired positon re-secure the
screw. (fi g.15)
90˚
45˚
180˚
MIN 10mm gap
W
W
Z
Z
90˚
45˚
180˚
MIN 10mm gap
W
W
Z
Z
90˚
45˚
180˚
MIN 10mm gap
W
W
Z
Z
Fixing the fi nial
(fi g.19)
1. Place one of the full rings on the pole after the bracket.
2. Slide the fi nial onto the pole and tighten the grub screw until
the fi nial is secure.
For Stud fi nials
(fi g.20)
1. Place one of the full rings on the pole after the bracket.
2. Push the fi nial onto the pole until it is secure.
19
20
Installing the curtain
1. Equally space curtain hooks along curtain header, you will
require one hook for every ring. (fi g.21)
2. Place hooks through the eyelet on the ring. (fi g.21)
3. Test the installation by drawing the curtains across the pole.
(fi g.22)
21
d1+d2+d1=Pole Length
Approx.
10cm
d2 (distance between end brackets)
Approx.
10cm
d1
d1
22
