Care and Maintenance
Cleaning After Use
Clean and disinfect areas you touch after each use. Use a non-abrasive
disinfectant cleaner (such as a mixture of 2oz of Lucasol™ disinfectant
with 1 gallon of water) that does not contain ammonia or ammonia de-
rivatives which may damage the acrylic surface. Spray the acrylic with
disinfectant until thoroughly wet. Allow to remain wet for 10 minutes
and then let air dry. Wipe other areas with a soft cloth slightly damp-
ened with disinfectant, then let air dry.
For heavily soiled areas remove the soil (lotions, etc.) using Lucas®
Spray and Wipe Tanning Bed Acrylic Cleaner. Apply solution with spray
bottle to wet the area thoroughly. Allow to remain wet for 30 seconds
and then wipe the surface dry. Then disinfect as described above.
Thorough Periodic Cleaning
The cooling fans draw air through the booth and will cause a dust
buildup on the lamps and reflectors. When a dust buildup is observed,
it is necessary to thoroughly clean the inside of the booth.
1
Remove the acrylic shield and lamps.
2
With a soft cloth, wipe the entire length of each lamp.
3
Clean both sides of the acrylic shield with a non-ammonia disinfec-
tant cleaner.
4
Wipe the reflectors with a clean damp cloth.
5
Re-install the lamps and acrylic shield.
Mechanical Inspection
Inspect the unit’s mechanical integrity every 400-500 hours of use.
•
Inspect the unit’s fasteners verifying that all are firmly in place. Pay
particular attention to the hinge bolts.
• Inspect the AC power cord and its connections.
• Inspect the acrylic. Replace if broken, cracked or badly scratched.
Removing/Replacing Acrylic Shield
The acrylic shield in each unit are secured in place by hinged profiles
which run the length of the long edges, both left and right. Start at
the end and simply
1
push the inside edge of the profile toward the
aluminum frame until it releases its latching action and then
2
lift.
Continue to lift the profile along its entire length until it swings back
freely. Repeat for the other profile. The long edges of the acrylic shield
are now exposed. Grasp the edge of the acrylic and carefully lift it out.
Replace the acrylic by placing it back into place. Close the hinged
profile by pushing it back into place until it snaps tight.
CAUTION
Be careful. The edges of the
acrylic shield may be sharp.
PROFILE
ACRYLIC
6
Operation
A Timer display -
Displays remaining time.
B Timer button -
Turns booth on. Timer
display shows remaining time. If a lesser
time is desired, press timer button until
desired time is displayed.
C Stop button -
Interrupts tanning session
(When used without remote or when connected to a remote system
using a control relay)
1
Step into the booth and close the door. Center yourself within the
booth to achieve an even tan.
2
Put on your safety goggles.
3
Press the timer button (B) to begin the tanning session. The timer
display (A) displays the remaining time. The lamps will turn on and
the timer will begin to count down from the maximum tanning ses-
sion time. If a tanning time less than the displayed time is desired,
repeatedly press the timer button (B) to decrease the remaining time.
4
When the timer reaches “0” the lamps turn off. If you want to stop
your session before time expires, press the stop button (C).
5
Exit the booth. The cooling fans run for three minutes after the lamps
shut off to aid in cooling the unit.
(When connected to the T-Max® Manager or T-Max® 1A or 3A.)
1
Step into the booth and close the door. Center yourself within the
booth to achieve an even tan.
2
Put on your safety goggles.
3
If the remote system has been set to allow a pre-tanning delay time,
the timer display (A) will repeatedly flash the delay symbol “dL” and
then the remaining delay time. Press the timer button (B) or wait until
the delay time has expired to begin the tanning session. The lamps
will turn on and the timer will begin to count down.
4
When the timer reaches “0” the lamps turn off. If you want to stop
your session before time expires, press the stop button (C).
5
Exit the booth. The cooling fans run for three minutes after the lamps
shut off to aid in cooling the sunbed. The timer will indicate “..” as a
reminder to clean the sunbed. After the sunbed is cleaned press the
timer button and the display will return to “0”
A
B
C
