manualshive.com logo in svg

Sun Microsystems Sun Fire V490, Руководство по установке и монтажу в стойку

Поделиться
Скачать
Sun Microsystems Sun Fire V490 Скачать руководство пользователя страница 41

31

C H A P T E R

3

Setup Procedures

This chapter tells you how to install the cable management arm, connect the power
cords and an Ethernet cable, and secure the cords and cables to the cable
management arm.

When you have completed the procedures in this chapter, you are ready to set up
a system console, power on the server, install the Solaris Operating System, and
install the electronic documentation. See the

Sun Fire V490 Server Quick Start Guide

or the

Sun Fire V490 Server Administration Guide

for information about these

procedures.

Make sure that you have installed the Sun Fire V490 server into a 4-post cabinet or
2-post rack (see Chapters 1 and 2) before following the instructions in this chapter.

This chapter contains the following procedures and information:

■

“Inventory for Setup Procedures” on page 32

■

“Install the Cable Management Arm” on page 33

■

“Connect the Power Cords” on page 41

■

“Connect a Twisted-Pair Ethernet Cable” on page 44

■

“Secure the Cables to the Cable Management Arm” on page 46

■

“Restore the Cabinet” on page 50

Содержание Sun Fire V490

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды