Sun Microsystems Sun Fire V445 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 66

Sun Microsystems Sun Fire V445 Скачать руководство пользователя страница 34

24

Sun Fire V445 Server Installation Guide • November 2006

Installing Optional Components

●

Install any optional components shipped with your system.

If you ordered options that are not factory-installed, see the

Sun Fire V445 Server

Service Manual

for installation instructions.

Note –

All internal components except disk drives, DVD drive, power supplies, fan

trays, and PCI cards must be installed by qualified service technicians only

.

Caution –

Place components on an antistatic surface, such as a Sun antistatic

discharge mat, an antistatic bag, or a disposable antistatic mat, to protect electronic
components from electrostatic damage.

Caution –

Always wear an antistatic wrist strap connected to a metal surface on the

chassis when you work on system components.

Connecting the Cords and Cables

Note –

Do not connect the system power cords until after you establish a connection

to the serial management port. See

for power-on instructions.

«
...
32
33
34
35
36
...
»

Содержание Sun Fire V445



































































Отзывы:

Нет отзывов