Sun Microsystems StorEdge D2 Скачать руководство пользователя страница 52

Страница: 52 / 118

3-2

Sun StorEdge D2 Array Installation, Operation, and Service Manual • February 2002

3.1

SunVTS Test Software

SunVTS™ is the Sun validation test suite. The SunVTS application verifies the
connectivity and functionality of hardware controllers and devices on Sun platforms.

SunVTS software and documentation is shipped with the Solaris operating
environment on the Software Supplement CD-ROM. The

Sun StorEdge D2 Array

Release Notes

specify which version of SunVTS is compatible with the current version

of the Sun StorEdge D2 array and which version of the Solaris operating
environment works with the current version of the array.

▼

To Install SunVTS Software

1. Download and read the

Sun StorEdge D2 Array Release Notes

and the

SunVTS User’s

Guide,

as described in “To Access Sun StorEdge Documents Online” on page xv.

Download the version of the

SunVTS User’s Guide

specified in the release notes

2. Make sure you have the correct

Software Supplement

CD-ROM for the version of

the Solaris operating environment that is specified in the release notes.

3. Follow the instructions in the chapter titled “Installing SunVTS” in the

SunVTS

User’s Guide

for how to install SunVTS

4. See the

Sun StorEdge D2 Array Release Notes

for required SunVTS patches that may

apply.

Содержание StorEdge D2























































































































Результаты поиска

Содержание StorEdge D2

Отзывы:

Похожие инструкции для StorEdge D2

Бренды по названию

Популярные бренды

Sun Microsystems StorEdge D2, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание StorEdge D2

Отзывы:

Похожие инструкции для StorEdge D2

Бренды по названию

Популярные бренды