Sun Microsystems StorEdge D2 Скачать руководство пользователя страница 44

Страница: 44 / 118

2-6

Sun StorEdge D2 Array Installation, Operation, and Service Manual • February 2002

▼

To Configure and Cable the Array

1. Make sure the option switch 1 is set properly for split-bus or single bus

configuration.

■

For single-bus configuration, make sure switch 1 is Up on the single ESM.

■

For a split-bus configuration (with two ESMs), make sure switch 1 is Down on
both ESMs.

FIGURE 2-1

ESM With Configuration Options Switches

Caution –

If you replace a failed ESM and the switch 1 is not set properly, data

corruption can occur.

2. Assign a number to the ESM using the Unit ID rotary switch.

See “Prepare the connected host to be able to test and monitor the D2 array.” on
page 2-4. Hint: When an array has two ESMs, assign the same number to both ESMs.
The number is used for finding an array not for finding an individual ESM.

3. Connect the SCSI cables between the host and the ESM.

See “Supported Configurations” on page 1-19, which shows where to connect the
SCSI cables depending on the configuration.

SCSI-A

SCSI-B

4 3 2 1

Configuration

Options

Unit ID

SCSI

8 9

4 3 2 1

Configuration

Options

Unit ID

For single-bus, set switch 1 Up.
For split-bus, set switch 1 Down.

Содержание StorEdge D2























































































































Результаты поиска

Содержание StorEdge D2

Отзывы:

Похожие инструкции для StorEdge D2

Бренды по названию

Популярные бренды

Sun Microsystems StorEdge D2, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание StorEdge D2

Отзывы:

Похожие инструкции для StorEdge D2

Бренды по названию

Популярные бренды