manualshive.com logo in svg

Sun Microsystems StorEdge 3000 Series, Руководство по лучшим практикам

Поделиться
Скачать
Sun Microsystems StorEdge 3000 Series Скачать руководство пользователя страница 54

38

    Sun StorEdge 3000 Family Best Practices Manual

 

• March 

2007

FIGURE

 

5-3 

Sample Sun StorEdge 3511 SATA Full-Duplex SAN Connections

The general procedure for creating this configuration follows.

1. Check the position of installed SFP modules. Move them as necessary to support 

the connections needed.

2. Connect expansion units if needed.

For information about connecting multiple expansion units, see 

“Sun StorEdge 3510 

FC Array High-Capacity Configurations” on page

 

43

 or 

“Sun StorEdge 3511 SATA 

Array High-Capacity Configurations” on page

 

57

. 

For information about connecting Sun StorEdge 3511 SATA expansion units to Sun 
StorEdge 3510 FC arrays, see 

“Combining Sun StorEdge 3510 FC Arrays and Sun 

StorEdge 3511 SATA Expansion Units” on page

 

67

.

3. Configure cache optimization.

4. Ensure that the fibre connection is set to point-to-point.

5. Ensure only one target ID per channel is configured.

6. Create at least two logical drives and configure spare disks. 

7. Create one or more logical drive partitions for each server.

8. Map Logical Drive 0 to channels 0 and 4 of the primary controller

H/D/RCC

H/D/RCC

Server 1

Server 2

Switch 1

Switch 2

Содержание StorEdge 3000 Series























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды