manualshive.com logo in svg

Sun Microsystems StorEdge 3000 Series, Руководство по лучшим практикам

Поделиться
Скачать
Sun Microsystems StorEdge 3000 Series Скачать руководство пользователя страница 46

30

    Sun StorEdge 3000 Family Best Practices Manual

 

• March 

2007

Note – 

Do not use a Sun StorEdge 3511 SATA array to store single instances of data. 

It is more suitable for use in configurations where the array has a backup or archival 
role.

Dual-Controller Multipath DAS Tips and 
Techniques

■

A Sun StorEdge 3510 FC array with two controllers can be configured to support 
up to 8 host connections. The Sun StorEdge 3511 SATA array can be configured to 
support up to 12 host connections. These connections can be used in pairs for 
redundancy, individually or in any combination of both.

■

You need to add SFP modules to support more than four host connections to the 
Sun StorEdge 3510 FC array or Sun StorEdge 3511 SATA array. For information 
about adding SFP modules, refer to the 

Sun StorEdge 3000 Family Installation, 

Operation, and Service Manual

 for the Sun StorEdge 3510 FC array and the Sun 

StorEdge 3511 SATA array.

■

Using two single-port 2-Gbit FC host adapters in a high-availability configuration 
makes optimum use of a Fibre Channel array’s redundancy. Mapping logical 
drive partitions to two paths while using multipathing software provides the best 
redundancy.

■

For complete redundancy and high availability, use host-based multipathing 
software such as Sun StorEdge Traffic Manager. To configure multipathing:

■

Establish two connections between a server and a Sun StorEdge Fibre Channel 
array.

■

Install and enable the software on the server.

■

Map the logical drive to both of the controller channels to which the server is 
connected.

Содержание StorEdge 3000 Series























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды