manualshive.com logo in svg

Sun Microsystems StorEdge 3000 Series, Руководство по лучшим практикам

Поделиться
Скачать
Sun Microsystems StorEdge 3000 Series Скачать руководство пользователя страница 42

26

    Sun StorEdge 3000 Family Best Practices Manual

 

• March 

2007

FIGURE

 

4-1 

Three Single-Controller DAS Configurations

Note – 

Do not use a Sun StorEdge 3511 SATA array to store single instances of data. 

It is more suitable for use in configurations where the array has a backup or archival 
role. 

Single-Controller DAS Tips and Techniques

■

A Sun StorEdge Fibre Channel array with a single controller can be configured to 
support up to four host connections (Sun StorEdge 3510 FC array) or six host 
connections (Sun StorEdge 3511 SATA array). These connections can be used in 
pairs, individually, or in any combination of both.

■

You need to add SFP modules to support more than two host connections to the 
Sun StorEdge 3510 FC array or Sun StorEdge 3511 SATA array. For information 
about adding SFP modules, refer to the 

Sun StorEdge 3000 Family Installation, 

Operation, and Service Manual 

for the Sun StorEdge 3510 FC array and the Sun 

StorEdge 3511 SATA array.

 

 

 

 

 

Single Server

Dual Servers

Quad Servers

Содержание StorEdge 3000 Series























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды