manualshive.com logo in svg

Sun Microsystems StorEdge 3000 Series, Руководство по лучшим практикам

Поделиться
Скачать
Sun Microsystems StorEdge 3000 Series Скачать руководство пользователя страница 33

17

C H A P T E R

3

Planning Your Storage Architecture

There are two popular methods for connecting storage to servers. 

■

Direct attached storage (DAS) uses a direct connection between a server and its 
storage system. The DAS solution of connecting each server to its own dedicated 
storage system is straightforward, and the absence of storage switches can 
minimize costs in some instances.

■

A storage area network (SAN) places a Fibre Channel (FC) storage switch 
between network servers and storage systems. A SAN solution shares a storage 
system among multiple servers using FC storage switches, and reduces the total 
number of storage systems required for a particular environment at the cost of 
additional element management (FC switches) and FC path complexity.

FIGURE

 

3-1 

DAS and SAN Storage Architectures

Selecting the best storage architecture for a particular environment can be a 
confusing exercise. In general, some environments are well-suited for DAS while 
others benefit greatly from SAN.

 

 

Direct-Attached Storage (DAS)

Storage Area Network (SAN)

Содержание StorEdge 3000 Series























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды