Sun Microsystems StorageTek L40 Скачать руководство пользователя

Страница: 52 / 92

Standard Installation Procedure

1-18

Revision L

96053

Attaching the Personality Module

The personality module is a connector that stores the library cell capacity information.
The module stores a capacity of either 20 or 40 cells. The library does not operate
properly unless an authorized module is attached to the rear of the EM.

Attach the module before powering-on the library for proper initialization

. Only remove the module

when installing an upgrade conversion bill or replacing the library.

CAUTION:

Possible component damage:

Make sure you follow the ESD procedure

described in

“ESD-Protection Procedure” on page xxiii

before

connecting the personality module.

The personality module is in a bag taped to the power supply handle. Remove the
personality module and attach it to its connector:

•

A 20-cell version uses part 31363270x.

•

A 40-cell version uses part 31363300x.

1. Personality module

Содержание StorageTek L40





























































































Результаты поиска

Содержание StorageTek L40

Отзывы:

Похожие инструкции для StorageTek L40

Бренды по названию

Популярные бренды

Sun Microsystems StorageTek L40, Руководство по установке

Результаты поиска

Содержание StorageTek L40

Отзывы:

Похожие инструкции для StorageTek L40

Бренды по названию

Популярные бренды