background image

1998 - 2000 FORD RANGER, 
MAZDA PICKUP
INSTALLATION INSTRUCTIONS
KIT SUM-7888300

WARNING

Installation of a body lift will change the center of grav-

ity and the handling characteristics of the vehicle. 

Because of the higher center of gravity and larger tires, 

the vehicle will handle and react differently both on and 

off-road.  You must drive it safely!  Extreme care must 

be taken to prevent vehicle rollover or loss of control, 

which could result in serious injury or death.  Avoid 

sudden sharp turns or abrupt maneuvers and always 

make sure all vehicle occupants have their seat belts 

fastened.

WARNING

Read and understand all instructions, warnings, cau-

tions, and notes in this sheet and in your owner’s man-

ual before you begin the installation of this body lift kit.

CAUTION

Proper installation of a body lift kit requires knowledge 

of the factory recommended procedures for disassem-

bly and assembly of original equipment components. 

We recommend that the factory shop manual and any 

special tools necessary to your vehicle be on hand 

during the installation.  Installation of this body lift kit 

without proper knowledge of the factory recommended 

procedures may affect the performance of these com-

ponents and the safety of your vehicle.  We strongly 

recommend that a certified mechanic familiar with the 

installation of similar components install this body lift 

kit.

WARNING

This body lift kit should only be installed on vehicles in 

good working condition.  Before installation, the vehi-

cle should be thoroughly inspected for evidence of cor-

rosion or deformation of the sheet metal around the 

factory body mounts.  This body lift kit should not be 

installed on any vehicle that is suspected to have been 

in a collision or misused.  Off-road use of your vehicle 

with this body lift installed may increase the stress 

applied to the factory body mounts.  We do not recom-

mend that any vehicle with a body lift installed be 

involved in any extreme off-road maneuvers such as 

jumping.  Failure to observe this warning may result in 

serious personal injury and/or severe damage to your 

vehicle.

WARNING

Many states now have laws restricting bumper heights 

and vehicle lifts.  Local laws should be consulted to 

determine if the changes you intend to make to your 

vehicle comply with state laws. Before combining a 

body lift with a suspension lift, consult an installation 

professional to see how this will affect your specific 

application.

WARNING

The installation of larger wheel and tire combinations 

may reduce the effectiveness of the anti-lock braking 

system.

WARNING

We will not warranty any damage to the a/c system.

WARNING

Always wear eye protection when operating power 

tools.

WARNING

Ensure that your vehicle tires are properly blocked and 

secured before you begin installation of this lift kit.

NOTE

We recommend using the Loctite® supplied in the kit 

on all hardware unless noted in the instructions.

Questions?

 Call our Tech Line 

1-330-630-0240

Содержание 1998 FORD RANGER










Отзывы: