Lynx
‐
CustomFit® Splice
‐
On Connector Ver.
2
‐
LYNX2
‐
ST for 250um or 900um Tight Buffered Fiber
‐
Installation Manual
For
your
safety
operation
Precautions
ETK1123071A
The
Lynx
‐
CustomFit® Splice
‐
On Connector
is designed
and
manufactured
to
assure
personal
safety.
Improper
operation
can
result
in
bodily
injury
and
serious
damage
to
this
product.
Please
read
and
observe
all
warnings
instructions
given
in
this
operation
manual.
Wear
safety
glasses
to
protect
your
eyes
when
h
dli
ti l fib
!
1. Improper
assembly
will
result
in
a
loss
of
performance.
Please
read
instructions
given
in
this
operation
manual
and the operation manual of the fusion splicer.
2.
Never touch the fiber of the stub
. It has been inspected
in the factory.
3. The
product
is
sensitive
to
dirt
or
dust.
Do
not
take
out
any parts from the package
until it is to be used
handling
optical
fiber.
Never
look
into
the
end
of
a
microscope
or
optical
cable
connected
to
an
optical
output
device
that
is
operating.
Laser
radiation
is
invisible,
and
direct
exposure
can
severely
injure
the
human
eye.
Alcohol
is
flammable
,
causes
irritation
and
is
harmful
!
!
any parts
from
the
package
until
it
is
to
be
used
.
4. The
characteristic
will
be
influenced
by
the
fiber
cleaved
surface
condition.
Please
use
a
cleaver
which
has
a
good
cleaving
characteristic.
5. Do
not
remove
the
dust
cap
until
the
connector
has
been
completely
assembled
in
order
not
to
cause
an
high
insertion
loss
due
to
them.
if
swallowed
or
inhaled.
Keep
alcohol
away
from
heat,
sparks,
skin,
and
avoid
contact
with
eyes.
In
the
case
of
the
work
at
the
high
place,
please
be
careful
not
to
drop
an
assembling
tool.
!
!
Composition
Assembling Tools
Disposable
Holder (Fiber Side)
LYNX2
‐
ST
Assembly
Tool
for 900um tight buffer
for 250um fiber
LYNX2
‐
UML
‐
S
FHS
‐
09
FHS
‐
025
LYNX2
‐
S
‐
LB5
Disposable
Holder
(*1)
Housing
Parts
Boot
Furcation
Tube
P
i
Either
one
holder
and
LYNX2
‐
ST
Assembly
Tool
are
required.
Fusion
Splicer
T
‐
Q101
‐
CA(71C), etc.
Fiber
Cleaver
FC
‐
6S
‐
C, etc.
Jacket
remover
JR
‐
M03, etc.
Recommended Program
Splicer
Fiber
Splicing
Program
Heater
Program
Below equipment or tool are examples.
Ferrule
Subassembly
Protection
Sleeve
(*1) 1 pc / 100 connectors
SMF
G 652 G 657
T
‐
25eS
SMF
SM1: SMF1C
Lynx
or FPS (60mm)
MMF
MM1: MMF1C
T
‐
39FH
SMF
LYNX
‐
SM
Lynx
or FPS (60mm)
MMF
LYNX
‐
MM
T
‐
Q101
‐
CA
(T
‐
71C)
SMF
Standard SMF
Lynx
or 60mm 0.9
MMF
MMF 50&62.5
Please
perform
Arc
test
prior
to
the
splicing
operation.
(See
the operation manual of the splicer.)
*Fiber
for
testing
is
not
included
in
the
kit.
Holder
Type
Cleave length: 10mm
Copyright
©
2011
Sumitomo
Electric
Industries,
LTD.
SMF
:
G.652,
G.657
MMF
:
MM50(OM2),
MM50(OM3),
MM50(OM4),
MM62.5(OM1)
Please
check
fiber
type
inside
the
field
fiber.
North Carolina (USA)
Sumitomo
Electric
Lightwave
Corp.
78 Alexander Drive, P.O. Box 13445, RTP, NC 27709
TEL
+1
‐
919
‐
541
‐
8100
http://www.sumitomoelectric.com/
Yokohama (Japan)
Sumitomo
Electric
Industries,
Ltd.
(Lightwave
Network
Products
Division)
1, Taya
‐
cho, Sakae
‐
ku, Yokohama 244
‐
8588, Japan
TEL
+81
‐
45
‐
853
‐
7223, http://global
‐
sei.com/fttx/
London (UK)
Sumitomo
Electric
Europe
Ltd.
220 Centennial Avenue, Elstree, Herts. WD6 3SL, UK
TEL
+44 (0)20
‐
8953
‐
8118
http://www.sumielectric.com/
