1.1 g
enerAl
notes
on
sAfety
This operation manual is applicable for the machine UPK
5-R. The machine may only be handled by personnel who
are qualified.
Hold power tools by insulated gripping surfaces when
performing an operation where the cutting tool may con-
tact hidden wiring or its own cord. Contact with a «live»
wire will make exposed metal parts of the tool «live» and
shock the operator.
WARNING Read all safety warnings and all in-
structions.
Failure to follow the warnings and in-
structions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
1.2 u
se
of
the
mAchine
for
purposes
for
which
it
is
intended
The machine is designed to satin finish, mat, texture,
brush, polish, and smooth metal, wood, plastics, and
such like, and also stone without water.
1.3 i
ncorrect
use
All uses other than those described under section
1.2 are regarded as incorrect use and are there-
fore not admissible.
1.4 ec
declArAtion
of
conformity
Otto Suhner GmbH of Trottäcker 50, D-79713 Bad Säck-
ingen, hereby declares under sole responsibility that the
product with the serial or batch no. (see reverse side) com-
plies with the requirements under the Directive 2014/30/
EU, 2006/42/EC, 2011/65/EU. Applied standards: EN ISO
12100, EN 60745, EN 55014-1, EN 55014-2, EN 61000-3-
2, EN 61000-3-3. Document Agent: M. Voyame. D-Bad
Säckingen, 06/2017.
M. Voyame/Division manager
2.1 p
rior
to
tAKing
the
mAchine
into
serVice
Before connecting tool to a power
source, be sure the voltage sup-
plied is the same as specified on
the name plate of the tool. The power sup-
ply should not vary more than 10% above or below the
voltage indicated on the nameplate. Check grinding tool
prior to use. The grinding tool must be mounted centrally
and positioned against the limit stop. The maximum al-
lowable speed of the tool and of the chuck may not be
exceeded under any circumstances. Observe national
1. n
oteS
on
S
afety
2. c
ommISSIonIng
regulations. Fit hand protection.
2.2 t
AKing
the
mAchine
into
serVice
Preselect speed with adjusting wheel according to speed
table.
Level 1: 1800 min
-1
Level 4: 3200 min
-1
Level 2: 2300 min
-1
Level 5: 3600 min
-1
Level 3: 2700 min
-1
Level 6: 4000 min
-1
During operation never exceed the speed which
has been matched to the grinding tool specifica-
tions!
2.2.1 t
unr
on
/t
urn
off
The switch must be in the OFF position. To turn the ma-
chine on, push the ON/OFF switch toward the front unteil
it clicks in. Press the ON/OFF swith to trigger the blocking
and the machine shuts down.
2.3 r
Ating
dAtA
Power voltage
120/230/240V, 50/60Hz
Power Input 230/240V
1530W
Power Output 230/240V
1000W
Power Input 120V
1340W
Power Output 120V
800W
No-load speed
4‘400 min
-1
Max. tool Ø
125mm
Grinding spindle thread
M14 / ø19
Sound pressure level EN 60745
86dB(A), K=3dB
Noise emission level
97dB(A), K=3dB
Vibration EN 60745
5.5m/s
2
, K=1.5m/s
2
Weight w/o cable
3.3kg
Protection class
II
20
CN
PL
CZ
FI
SE
NL
PT
ES
IT
EN
FR
DE
GB
