background image

7

ENGLISH

FRANÇAISE

ESPAÑOL

6. OPERATING YOUR ENGINE

(See Fig. 

or 

5

)

Pulley fitting onto PTO shoulder

For proper pulley fitting onto PTO shoulder, make round 

chamfer at pulley corner. 
Sharp edge of pulley corner strikes PTO shoulder. In this 
improper condition, bolt will be loosened, and PTO damaged 

finally.

Pulley

Crankshaft (PTO)

Pulley

Crankshaft (PTO)

Round chamfer for 

proper fitting

Sharp edge striking

Proper

Improper

1. STARTING

MANUAL START

(1)  Open the fuel valve. (See Fig.

4

-

)

(2)  Insert the safety key. (See Fig.

4

-

)

(3)  Move the choke lever to CHOKE position. (See Fig.

4

-

)

(4)  Depress primer two times. (See Fig.

4

-

)

 CAUTION

 

If the engine is already warm, place choke 

control in the OFF position instead of CHOKE 

position.

 

Do not push the primer bulb.

(5) Move throttle to FAST position. (See Fig.

4

-

)

(6)  Pull the starter handle slowly until resistance is felt. This is 

the “compression” point. Return the handle to its original 
position and pull swiftly. Do not pull out the rope all the way. 
After starting the engine, allow the starter handle to return to 
its original position while still holding the handle.  
(See Fig.

4

-

)

(7)  After starting the engine, gradually open choke by turning 

the choke lever and finally keep it fully opened.

 

Do not fully open the choke lever immediately when the 
engine is cold or the ambient temperature is low, because 
the engine may stop. (See Fig.

4

-

)

ELECTRIC START

(1) Open the fuel valve. (See Fig.

4

-

)

(2) Insert the safety key. (See Fig.

4

-

)

(3) Move the choke lever to CHOKE position. (See Fig.

4

-

)

(4) Depress primer two times. (See Fig.

4

-

)

 CAUTION

 

If the engine is already warm, place choke 

control in the OFF position instead of CHOKE 

position.

 

Do not push the primer bulb.

(5)  Move throttle to FAST position. (See Fig.

4

-

)

(6)  Connect power cord to starter motor, then to wall receptacle. 

(See Fig.

5

-

)

(7)  Depress starter button. (See Fig.

5

-

)

 CAUTION

 

To prolong starter life, use short starting cycles 

(5 seconds maximum, then wait one minute).

 WARNING

 

Prevent damage to 

unit. Know voltage of 

your starter and only 

use matching outlets.

 

Use a 3-wire power 

cord.

120V AC

3-WIRE

RECEPTACLE

3-PRONG

GROUNDED PLUG

 

Plug Power cord into starter motor first, then 

into wall receptacle.  

If additional power cord is required, use a 3-wire

 

If the supply cord is damaged, it must be 

replaced by the manufacturer or its service 

agent or a similarly qualified person in order to 

avoid a hazard.

(8)  After starting the engine, gradually open choke by turning 

the choke lever and finally keep it fully opened.

 

Do not fully open the choke lever immediately when the 
engine is cold or the ambient temperature is low, because 
the engine may stop. (See Fig.

4

-

 )

(9)  

IMPORTANT

:  Disconnect power cord from wall receptacle, 

then starter motor. (See Fig.

5

-

)

2. STOPPING

(1)  Move throttle control to SLOW, then to STOP.  

(See Fig.

6

-

)

(2) Pull out safety key. (See Fig.

6

-

)

(3) Close fuel valve. (See Fig.

6

-

)

Содержание Robin Engines SX17























Отзывы: