manualshive.com logo in svg

Stryker 6086, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Stryker 6086 Скачать руководство пользователя страница 8

8

6086-009-001 REV B

www.stryker.com

Return To Table of Contents

This manual is designed to assist you with the operation and maintenance of the Stryker 

Performance-PRO™ XT

  cot.  

Read this manual thoroughly before using the equipment or beginning maintenance on it. To ensure safe operation of 
this equipment, it is recommended that methods and procedures be established for educating and training staff on the 
safe operation of this cot. 

PRODUCT DESCRIPTION

The Stryker Model 6086 

Performance-PRO™ XT 

is a manual ambulance cot that consists of a platform mounted on 

a wheeled X-frame designed to support and transport a maximum weight of 700 pounds in pre-hospital and hospital 
environments. The device is collapsible for use in emergency vehicles and has an adjustable load height feature to 
allow the device to be set to different ambulance deck heights for proper body mechanics during loading and unload-
ing.  Duplicate foot-end controls on the upper and lower lift bars accommodate different operator positions or sizes and 
the side release handle allows a single operator to raise and lower an unoccupied cot. The device is equipped with 
the following: a retractable head section for 360-degree mobility in any height position, side rails, patient securement 
straps, an adjustable pneumatic backrest and various optional accessories that assist with transport of the patient.  
Maximum patient comfort is attainable with the three different litter positions of shock, flat leg and optional knee gatch 
positioning.

INTENDED USE OF PRODUCT

The Stryker Model 6086 

Performance-PRO™ XT

 is a non-powered wheeled stretcher, which is intended to support and 

transport the entire body of a traumatized, ambulatory or non-ambulatory human patient (includes infants and adults). 
The device is designed to support patients in a supine (horizontal) or sitting position and facilitate the transportation 
of associated medical equipment (i.e. oxygen bottles, monitors, and/or pumps) in emergency/transport vehicles. This 
ambulance cot is intended to be used in pre-hospital and hospital environments, in emergency and non-emergency 
applications. It is rated to a maximum capacity of 700 pounds (sum of the patient, mattress and accessory weight) and 
the intended operators of the device are trained professionals including: emergency medical service and medical care 
center personnel, as well as medical first responders. The expected service life of the product is 7 years. 

Ambulance cots are intended for transportation purposes. They are not intended for extended stay or to be used 
as hospital beds. They are also not intended to be used in devices which modify air pressure, such as hyperbaric 
chambers. 

Introduction

Содержание 6086































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды