manualshive.com logo in svg

Stryker 6086, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Stryker 6086 Скачать руководство пользователя страница 64

64

6086-009-001 REV B

www.stryker.com

Return To Table of Contents

Service Information

BACKREST ADJUSTMENT

Tools Required:

 

• 

1/2” Combination Wrench 

 

• 

5/32” Hex Wrench 

• 

3/32” Hex Wrench

• 

Small Slotted Screwdriver

Procedure:

1.  For easier access, move the backrest to 73 degrees.

Note:  

Before continuing with the backrest adjustment 

procedure, be sure that the cylinder (A) is completely 
threaded into the yoke (B) so no threads are showing 
on the shaft of the cylinder.  If threads are showing, 
use a 3/32” hex wrench to remove the set screw 
(C) in the center of the yoke.  Using a small slotted 
screwdriver, remove the E-clip and pin (D & E) that 
holds the bottom of the pneumatic cylinder. Thread 
the cylinder shaft (A) completely into the yoke (B).  
Replace the E-clip and pin (D & E) and replace the 
set screw (C) using Loctite

®

. (Figure 61 and Figure 

62)

2.  Using a 1/2” combination wrench, loosen the hex nut 

(F) on the backrest pivot (J) while holding the set 
screw (H) fixed in the pivot (Figure 62). 

3.  Using a 5/32” hex wrench, turn the set screw (H) until 

there is no play between the backrest release handle 
(K) and the pneumatic cylinder release button (Figure 
62). 

Note:  

Make sure that the backrest travels from flat to 

at least 73 degrees.  If it does not, turn the set screw 
clockwise 1/2 turn.  Repeat until at least 73 degrees 
of travel is achieved. 

4.  Lower the backrest to a 5−10 degree angle and release 

the handle.  Apply approximately 50 lb of downward 
force to the end of the backrest.  If the backrest drifts 
down, turn the set screw counterclockwise.  Repeat 
until the backrest does not drift downward. 

5.  Using the 1/2” combination wrench, tighten the hex 

nut (F) while holding the set screw fixed in the pivot 
(Figure 62). 

6.  Verify proper operation of the unit before returning it 

to service.

B

A

D

E

Figure 62

K

C

H

F

J

Figure 61

Содержание 6086































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды