manualshive.com logo in svg

Stryker 6086, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Stryker 6086 Скачать руководство пользователя страница 49

www.stryker.com

6086-009-001 REV B

49

Return To Table of Contents

Optional Accessories

USING THE KICKSTAND FOR DIALYSIS SCALE

The kickstand is intended for weighing patients on a scale.

Note:  

• 

The kickstand assembly is configured for an X-frame cot retention system only. 

• 

The kickstand (p/n 6085-002-000) is not compatible with the optional base storage net (p/n 6500-160-000).

 WARNING

• 

Stryker recommends a two person operation when using the kickstand.

• 

Make sure that the patient weight is centered on the cot before using the kickstand.

• 

Engage the kickstand with your foot only.

• 

Lower cot height prior to engaging kickstand for increased stability.

• 

Make sure that the kickstand remains in the retracted position and does not engage during transport.

• 

Do not use the kickstand as a brake.

• 

Do not engage kickstand on a sloped surface.

To use the kickstand:

1.  Operator 1 engages the kickstand with their foot as shown in Figure 51. 
2.  Operator 2 lifts the foot end of the cot at a height sufficient to actuate the kickstand.
3.  Both operators must make sure that the kickstand is in the forward locked position as shown in Figure 52. 

To release the kickstand:

1.  Operator 1 lifts the foot end of the cot until both wheels 

are off of the floor.

2.  Operator 2 rolls the cot slightly forward to make sure 

that the kickstand retracts on its own as shown in 
Figure 53.

Figure 51

Figure 52

Figure 53

Содержание 6086































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды