manualshive.com logo in svg

Stryker 6086, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Stryker 6086 Скачать руководство пользователя страница 20

20

6086-009-001 REV B

www.stryker.com

Return To Table of Contents

Figure 7:  Vehicle Deck Height

DH

2

2

Safety Hook

Sill

Sill Edge

Figure 8:  Vehicle Deck Height

Vehicle Safety Hook Installation

Note: 

These installation instructions

 

are intended for cots that you will NOT use with Power-LOAD.  For Model 6086 

cots with the Power-LOAD option, see the Power-LOAD Operations/Maintenance Manual for installation instructions.

VEHICLE CONFIGURATION

According to federal regulations (reference KKK-A-1822), the bumper height of the vehicle shall be installed equidistant 

±

 5 cm (2 inches) from the vehicle floor to the ground level, which is defined as the vehicle deck height. The bumper 

step shall have a minimum depth of 13 cm (5 inches) and a maximum depth of 25 cm (10 inches). If the bumper depth 
is greater than 18 cm (7 inches), then the bumper must be able to fold. Installation of the safety hook into any vehicle 
compliant with this federal specification provides adequate clearance for the cot base to lower to its fully extended 
position. The cot is compatible with all vehicle deck heights (see specifications for maximum load height) as long as 
the vehicle meets the federal specifications that are outlined in KKK-A-1822.

 CAUTION

• 

Set the cot load height to the proper stop height prior to operation.

• 

Installation of the safety hook should be done by a certified mechanic familiar with ambulance vehicle construction. 
Consult the vehicle manufacturer before installing the safety hook and be sure that the installation of the safety hook 
does not damage or interfere with the brake lines, oxygen lines, fuel lines, fuel tank or electrical wiring of the vehicle.

REQUIRED HARDWARE FOR INSTALLATION OF THE SAFETY HOOK (NOT SUPPLIED)

(2) Grade 5, Minimum 1/4”-20 Socket Head Cap Screws* for the short or long safety hook
(2) Grade 5, Minimum 1/4”-20 Flat Socket Head Cap Screws* for the J hook
(2) Flat Washers 
(2) Lock Washers
(2) 1/4”-20 Nuts

* The length of the socket head cap screws depends on the thickness of the vehicle floor.  Use screws that are long 
enough to go completely through the patient compartment floor, washer and nut by at least two full threads.

Содержание 6086































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды