manualshive.com logo in svg

Struers LaboForce-100, Инструкция по эксплуатации

Поделиться
Скачать
Struers LaboForce-100 Скачать руководство пользователя страница 7

DANGER

This sign indicates a hazard with a high level of risk which, if not avoided, will
result in death or serious injury.

WARNING

This sign indicates a hazard with a medium level of risk which, if not avoided,
could result in death or serious injury.

CAUTION

This sign indicates a hazard with a low level of risk which, if not avoided, could
result in minor or moderate injury.

CRUSHING HAZARD

This sign indicates a crushing hazard which, if not avoided, could result in minor,
moderate or serious injury.

HEAT HAZARD

This sign indicates a heat hazard which, if not avoided, can result in minor,
moderate or serious injury.

General messages

Note

This sign indicates that there is a risk of damage to property, or a need to proceed
with special care.

Hint

This sign indicates that additional information and hints are available.

2.4

Safety messages in this manual

WARNING

Struers equipment must only be used in connection with and as described in the
Instruction Manual supplied with the equipment.

CRUSHING HAZARD

Wear safety shoes when handling heavy machinery.

2   Safety

LaboForce-100

7

Содержание LaboForce-100



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды