Struers LaboForce-100 Скачать руководство пользователя страница 5

Страница: 5 / 34

About this manual

Instruction Manuals

Struers equipment must only be used in connection with and as described in the Instruction
Manual supplied with the equipment.

Note

Read the instruction manual carefully before use.

Note

If you wish to view specific information in detail, see the online version of this
manual.

Safety

2.1

Intended use

The device is for professional semi-automatic materialographic preparation (grinding or polishing)
of materials for further materialographic inspection.

LaboForce-100 is intended to be used in combination with:

•

LaboPol-30

•

LaboPol-60

•

LaboDoser-100

Do not use the device for
the following

Other equipment than stated in the section "Intended use".

Model

LaboForce-100

2.2

LaboForce-100 safety precautions

2.2.1

Read carefully before use

Ignoring this information and mishandling of the equipment can lead to severe bodily injuries and
material damage.

1 About this manual

LaboForce-100

Содержание LaboForce-100



































Результаты поиска

Содержание LaboForce-100

Отзывы:

Бренды по названию

Популярные бренды

Struers LaboForce-100, Инструкция по эксплуатации

Результаты поиска

Содержание LaboForce-100

Отзывы:

Бренды по названию

Популярные бренды