manualshive.com logo in svg

Struers LaboForce-100, Инструкция по эксплуатации

Поделиться
Скачать
Struers LaboForce-100 Скачать руководство пользователя страница 17

5.7.1

Inserting a flexible specimen holder

Inserting a flexible specimen holder

CAUTION

To prevent specimens from detaching from the specimen holder, make sure that
the specimen or specimens are covered completely by the flexible specimen
holder.

CRUSHING HAZARD

Keep your hands clear of the flexible specimen holder when lowering the
specimen mover.

Procedure

Hint

Make sure that you use sufficient force according to the specimen size and
Struers recommendations.
The Struers Metalog Guide methods are based on a specimen with an area of 7
cm

2

.

Adjust the method according to your specific specimen area.
Procedure

Hint

Make sure that the preparation surface is sufficiently wet before you start the
preparation process.

1.

Press the

Lower/Raise

button to make sure that the specimen mover head is

fully raised.

2.

Press the black button on the specimen mover head.

3.

Insert the flexible specimen holder and rotate it until the three pins are aligned
with the holes in the specimen mover.

4.

Push the flexible specimen holder upwards until it locks into position.

5.

Release the black button on the specimen mover head. Make sure that the
flexible specimen holder is securely fixed.

5.7.2

Adjusting the height of the flexible specimen holder

The following applies only when a flexible specimen holder is used.

5   Installation

LaboForce-100

17

Содержание LaboForce-100



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды