manualshive.com logo in svg

Struers LaboForce-100, Инструкция по эксплуатации

Поделиться
Скачать
Struers LaboForce-100 Скачать руководство пользователя страница 14

6.

Move the adjustment ring up until the pin fits into the V-
shaped groove on the cabinet of the control panel.

7.

Tighten the adjustment ring to fix it in this position.

8.

Press the

Turn/push knob

knob to clear the error

message.

9.

Press the

Lower/Raise

button to raise the specimen

mover head.

5.6.4

Adjusting the horizontal position of the specimen holder or specimen mover plate

With a specimen holder or specimen mover plate mounted:

1.

Press the

Lower/Raise

button to lower the specimen

mover head.

2.

Loosen the 2 fastening screws holding the column of the
control panel.

3.

Replace the manual splash guard with a splash guard for
semi-automatic preparation or splash guard for Wet
grinding disc.

4.

Moves the specimen mover head to the right.

With an MD-disc

1.

Place the specimen mover plate in a position that allows
the specimen to run 3 – 4 mm over the edge of the
preparation disc.

A

Disc edge

B

Specimen mover plate

14

LaboForce-100

5   Installation

Содержание LaboForce-100



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды