background image

ELECTRIC WINCH RATING*

   5%  10% 20% 30% 50% 70% 

 

   (3°)  (6°)  (11°)  (17°)  (26°) (35°) 

 

  

8,000 lbs.   6,000 lbs.   4,000 lbs.  3,100 lbs.  2,200 lbs.  1,800 lbs.  1,200 lbs. 

 

 

3,629 kg  2,722 kg  1,814 kg  1,406 kg    998 kg    816 kg 

544 kg

 

  

12,000 lbs. 9,000 lbs.    6,100 lbs.  4,600 lbs.  3,300 lbs.  2,700 lbs.  1,800 lbs.

 

  

5,443 kg  4,082 kg  2,767 kg  2,087 kg  1,497 kg  1,225 kg 

817 kg

 

  

18,000 lbs. 13,500 lbs.  9,100 lbs.  6,900 lbs.  5,000 lbs.  4,100 lbs.  2,700 lbs. 

  

8,165 kg  6,124 kg  4,128 kg  3,130 kg  2,268 kg  1,860 kg 

1,225 kg

 

  

26,700 lbs.   20,100 lbs. 13,600 lbs. 10,300 lbs.  7,400 lbs.  6,100 lbs.  4,000 lbs. 

 

 

12,111 kg  9,117 kg  6,169 kg  4,672 kg  3,357 kg  2,767 kg 

1,814 kg

120 Volt AC 

ELECTRIC WINCHES

®

DOUBLE LINE OPERATION

Models SA7000AC, SA7015AC, SA12000AC and 

SA12015AC are factory equipped with a pulley 

block and hook and 50’ of cable for double line 

operation. This increases the pulling capacity of the 

winch as shown, however, care must be taken to 

allow adequate motor cooling. Note that with dou-

ble line, a pull of 25’ requires reeling in 50’ of cable.
For intermittent use only. Ratings at left are based 

on 10’ pull. For longer pulls motor cooling periods 

must be allowed.

MAXIMUM CONTINUOUS RUN TIME  3 MINUTES

 

CAUTION: CONTINUOUS RUNNING IN 

EXCESS OF 3 MINUTES WILL DAMAGE WINCH 

MOTOR.

GUIDE TO ROLLING LOAD CAPACITY**

Maximum weight in pounds and kilograms rolling load.

APPROXIMATE LOAD 

SPEED 

(FT./MIN.)

 

MODEL

 

 PERCENT INCLINE

LOAD

CAPACITY*

(*)  Load capacity (dead weight) is a measure of actual maximum force to which the 

winch system may be subjected.

(**)  All capacities shown are with 15’ of cable on the reel and 10% rolling friction factor. 

For full reel of cable adjust capacities according to graph above. Note 5% incline is 

one-half foot rise in ten feet.

WINCH RATINGS

OWNER’S 

MANUAL

MODELS SA5000AC, SA5015AC,  

SA7000AC, SA7015AC, SA9000AC,  

SA9015AC, SA12000AC, SA12015AC

 

5000
4500
4000
3500
3000
2500
2000
1500
1000

500

DEAD WEIGHT CAPACITY (LBS.)*

LENGTH OF CABLE ON REEL (FT.)

10  

20  

30  

40   50

SA9000AC & SA9015AC single line

SA12000AC & SA12015AC double line

SA7000AC & SA7015AC double line

SA5000AC & SA5015AC single line

 

WARNING: NOT TO BE 

 

USED AS A HOIST FOR 

LIFTING, SUPPORTING OR 

TRANSPORTING PEOPLE OR 

LOADS OVER AREAS WHERE 

PEOPLE COULD BE PRESENT!

 

NO LOAD  FULL LOAD

 

Full  Empty  Full Empty

 

Reel  Reel  Reel Reel

 

35 16 16  9

 

17.5 8  9.5  6

 

18 6  7 3.5

 

9 3 4  2

     WARNING: 

READ INSTRUCTIONS CAREFULLY BEFORE

ATTEMPTING TO INSTALL, OPERATE OR SERVICE THE STRONGARM

 

ELECTRIC WINCH. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT 

IN SERIOUS OR FATAL INJURY. RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

E

N

G

L

I

S

H

F

R
A
N
Ç
A

I

S

1

SA5000AC

SA5015AC
SA7000AC

SA7015AC

SA9000AC

SA9015AC
SA12000AC

SA12015AC

SA5000AC

SA5015AC

SA7000AC

SA7015AC

SA9000AC

SA9015AC

SA12000AC

SA12015AC

Содержание SA5015AC









Отзывы: