manualshive.com logo in svg

Strautmann Super-Vitesse CFS 3101, Руководство по эксплуатации, Страница: 94 / 225

Поделиться
Скачать
Strautmann Super-Vitesse CFS 3101 Скачать руководство пользователя страница 94

Commissioning

 

 

 

94 

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO   10.13 

 

  1.  Fix the control set (1) in the cabin within 

view and reach to the right of the driver 

seat. 

  2.  Connect the signal plug (2) of the control 

set with the signal socket (3) of the mobile 

cable harness or with the signal socket of 

the tractor (if available). 

  3.  Plug the 3-pole plug (4) (DIN 9680) of the 

mobile cable harness into the 3-pole socket 

of the tractor. 

 

  (Pole 15/30 = Plus; Pole 31 = Minus) 

 

  This is not necessary if the tractor is 

equipped with an ISOBUS cable harness. 

  4.  Depending on the machine's equipment, 

plug: 

 

the ISO socket (5) of the mobile cable 

harness into the ISO plug of the 

control unit on the machine. 

 

the ISO plug of the control unit into the 

ISO socket of the tractor. 

 

 

 

Fig. 63 

 

  

6.4 

Adjust mounting height of folding drawbar 

 

 

Shop work 

  

You must have the mounting height of the folding drawbar adjusted to the respective tractor model by 

an authorised workshop, in order to ensure that the lowered pick-up can properly adapt to uneven 

terrain. Only a properly adjusted mounting height of the folding drawbar guarantees best possible 

picking-up of the material to be loaded. 

 

 

 

Only an authorised workshop is allowed to adjust the mounting height 

of the folding drawbar! 

 

 

 

WARNING 

 

Risk of being crushed, drawn in, becoming entangled and risk of 

impact to people if the hitched machine accidentally loosens 

from the tractor due to worn drawbar lug and coupling bolt! 

Ensure that there is enough free space between the drawbar lug and 

the coupling bolt when lifting the folding drawbar. 

 

 

 

Assembly instructions for authorized workshop: 

 

 

The distance X must be 1180 mm between the 

ground and the machine frame with the forage 

wagon with lowered folding drawbar hitched up 

to the tractor. 
The mounting height of the folding drawbar in 

relation to the machine frame must be aligned by 

means of the threaded spindles of the hydraulic 

cylinders if the actual distance X is not 1180 mm. 
Use the rear borehole of the respective screw-on 

seat (1) if you cannot reach the required distance 

X, in particular in case of bottom linkage. 

 

 

 

Fig. 64 

 

 

 

Содержание Super-Vitesse CFS 3101


































































































































































































































Отзывы:

Нет отзывов