Strautmann Super-Vitesse CFS 3101 Скачать руководство пользователя страница 27

Страница: 27 / 225

Safety instructions

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13

Safety instructions

This chapter contains important information for the user and the operator on how to operate the

machine in a safety-conscious and trouble-free way.

Observe all safety instructions included in these operating

instructions!

Most accidents are caused by non-observance of simplest safety

rules.
By observing all safety instructions included in these operating

instructions, you help to prevent accidents.

3.1

Safety-conscious working

Only operate the machine in perfect safety-related condition.

WARNING

Risk of being crushed, cut, becoming entangled, being drawn in

or risk of impact if the tractor and the machine are not in

adequate roadworthy and reliable condition!

Check tractor and machine for their road and operational safety

before each startup.

3.2

Organisational measures

The operating instructions:



must always be kept at the machine's place of operation,



must always be easily accessible for operating and maintenance

staff.

3.2.1

User’s obligation

The user is obliged:



to observe the general national occupational safety, accident prevention and environmental

protection rules,



to exclusively have staff operating the machine who:



know the basic occupational safety and accident prevention regulations,



have been instructed how to operate the machine,



have read and understood these operating instructions.



to keep all warning signs attached to the machine in legible condition,



to replace any damaged warning signs,



to provide the necessary personal protective equipment such as protective goggles, work gloves

according to DIN EN 388, safety footwear, protective clothing, skin protectant, etc.

3.2.2

Operator’s obligation

Any members of staff charged to operate the machine are obliged:



to acquaint themselves with the machine before starting operation,

Содержание Super-Vitesse CFS 3101


































































































































































































































Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы:

Strautmann Super-Vitesse CFS 3101, Руководство по эксплуатации, Страница: 27 / 225

Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы: