Strautmann Super-Vitesse CFS 3101 Скачать руководство пользователя страница 148

Страница: 148 / 225

Settings

148

Super-Vitesse CFS 3101, 3501 / Super-Vitesse CFS 3101 DO, 3501 DO 10.13

The pulley must easily turn to guide the holding-down device

properly!

Set the distance between pick-up and holding-down device/pulley by

means of the chain length:



Large swathe = large distance; if the distance is too small,

picking-up of the material to be loaded is impeded



Small swathe = small distance; if the distance is too large, the

material to be loaded is not picked up properly

1. Set the desired distance between pick-up

and holding-down device/pulley by means

of the chain length (4).

Fig. 92

9.2

Set cutting length

The number of cutting knives mounted in the cutting unit determines the cutting length of the loaded

material. 40 cutting knives at one level ensure a cutting length of 39 mm. For information about

removal and installation of cutting knives, see chapter "Remove and install cutting knives", page 182.

Содержание Super-Vitesse CFS 3101


































































































































































































































Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы:

Strautmann Super-Vitesse CFS 3101, Руководство по эксплуатации, Страница: 148 / 225

Результаты поиска

Содержание Super-Vitesse CFS 3101

Отзывы: