Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 327

background image

Safety instructions

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

74

•

Before switching the propeller shaft on, observe the safety instructions for p.t.o. shaft operation
included in the chapter "Safety instructions for the operator".

•

Immediately have damaged or missing parts of the propeller shaft replaced by original parts
from the propeller shaft manufacturer.

Observe the fact that only an authorised workshop is allowed to repair a propeller shaft.

3.4.6

Hitched machines

•

Observe the admissible combination options of the tractor's coupling device and the machine's
drawgear!

Only couple admissible vehicle combinations (tractor and hitched machine).

•

Observe the maximum admissible tongue load of the tractor at the coupling device in case of
single-axle machines!

•

Always ensure sufficient steerability and braking ability of the tractor!

Machines attached or hitched to a tractor influence the driving characteristics as well as the
steerability and the braking ability of the tractor, in particular rigid-drawbar trailers with tongue
load!

•

Only an authorised workshop is allowed to adjust the height of the drawgear for towing-hook
drawbars with tongue load!

•

Ensure sufficient tongue load at the support device when unhitching and parking a single-axle
machine!

«
...
72
73
74
75
76
...
»

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Giga-Vitesse CFS 3602

Бренд: Rangevision Страницы: 28

Бренд: Ibiza Страницы: 21

Бренд: IBC Страницы: 8

Бренд: Ibanez Страницы: 8

Бренд: IAI Страницы: 5

Бренд: iFIT Страницы: 11

Бренд: Laserworld Страницы: 8

Бренд: Laserworld Страницы: 6

Бренд: LaserLiner Страницы: 56

Бренд: LaserLiner Страницы: 54

Бренд: Saadat Страницы: 61

Бренд: Saadat Страницы: 22

Бренд: XanLite Страницы: 4

Бренд: Balanced Body Страницы: 4

Бренд: Balanced Body Страницы: 2

Reformer Trapeze Combination

Бренд: Balanced Body Страницы: 164

Бренд: Wacker Neuson Страницы: 50

Бренд: Balanced Body Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды