Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 53

Страница: 53 / 327

Product description

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

2.19.3

Required tractor equipment

The employed tractor must meet the following requirements, in order to ensure correct use of the
machine:

2.19.3.1 Tractor engine output and p.t.o. speed

Giga-Vitesse CFS

3602

3602 DO

4002

4002 DO

4402

4402 DO

Power required

110

121

140

150

165

180

P.t.o. speed

min

-1

1000

2.19.3.2 Electrical system

Battery voltage: 12 V (volt)

Socket for lighting: 7-pole

Socket for control set: 3-pole (DIN 9680). The feed line of the 3-pole socket should have a minimum
cable cross section of 4 mm².

2.19.3.3 Hydraulic system

Check the compatibility of the hydraulic oils before connecting the
machine to the hydraulic system of your tractor.

Do not mix mineral oils with bio oils!

Maximum operating pressure: 200 bar

Delivery rate: min. 40 l/min at 180 bar, max. 100 l/min at 200 bar

Hydraulic oil of machine: HLP 46

Delivery rate with electro-hydraulic forced steering axle system: min. 60 l/min, max. 100 l/min

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды

Strautmann Giga-Vitesse CFS 3602, Руководство по эксплуатации

Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды