Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 275 | Manualshive

Страница: 275 / 327

background image

Service and maintenance of machine

275

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

Clean filter element (shop work)

Clean heavily soiled filter elements approx. every
3-4 months, depending on the operating
conditions.

1.

Open the lid (3).

2.

Remove the two Phillips screws (4).

3.

Open the cover (5) by swivelling.

4.

Remove the filter element (2) from the
hose coupling.

5.

Clean the filter element with benzene or
thinner (rinse).

6.

Use compressed air to blow the filter
element dry.

7.

Reinsert the filter element into the hose
coupling.

Fig. 140

8.

Close the cover.

9.

Screw the cover by means of the two Phillips screws.

10.

Connect the feed and brake line to the tractor.

11.

Check the hose couplings for tightness.

8.14.2

Drain compressed-air reservoir of compressed-air brake system

Drain the compressed-air reservoir every day before the first
journey!

The compressed-air reservoir is situated beneath the machine in
front of the axle support.

Take the ring (2) and pull the drain valve of the
compressed-air reservoir (1) down until water is
no longer pouring out of the compressed-air
reservoir.

Fig. 141

«
...
273
274
275
276
277
...
»

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Giga-Vitesse CFS 3602

Бренд: GALLERY Страницы: 18

Бренд: MacDon Страницы: 2

Бренд: MacDon Страницы: 214

Бренд: MacDon Страницы: 32

Бренд: JB Systems Страницы: 12

Бренд: Bang & Olufsen Страницы: 2

Бренд: Bacharach Страницы: 48

Бренд: LAWO Страницы: 459

Бренд: earline Страницы: 13

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 20

Бренд: Fellowes Страницы: 20

Бренд: Nederman Страницы: 89

Бренд: Nederman Страницы: 71

Бренд: Nederman Страницы: 131

Бренд: X-Cite Страницы: 2

Бренд: York Страницы: 26

Бренд: Tactile Medical Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды