Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 327

Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 110

Commissioning

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

110

5.12

Hitch machine

•

Observe the information in the chapter "Basic safety
instructions for the operator" when hitching and unhitching the
machine.

•

Check the machine for visible defects during each hitching and
unhitching procedure. Observe the information in the chapter
"Operator's obligation".

Only in case of load-sensing hydraulic system:

•

Check the pressure regulator for correct setting. Observe the
information in the chapter "Load-sensing hydraulic system".



Lock the pressure regulator in the electro-hydraulic
control block if the hydraulic connector "Flow line" is
connected with the pressure line to the tractor's hydraulic
pump.



Open the pressure regulator in the electro-hydraulic
control block if the hydraulic connector "Flow line" is
connected to the control device of the tractor.

1.

Secure the machine against accidental rolling

2.

Always check the machine for visible defects during hitching.

3.

Couple the forced steering axle (if available).

4.

Couple the drawgear.

5.

Connect the hydraulic hose pipes.

6.

Connect the service brake system.

7.

Couple the propeller shaft.

8.

Connect the control set.

9.



Connect the lighting system.

10.

Lift the supporting leg.

11.

Release the parking brake.

«
...
108
109
110
111
112
...
»

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Отзывы:

Нет отзывов