manualshive.com logo in svg

Stratus ftServer 2900 Series, Планирование и руководство по установке

Поделиться
Скачать
Stratus ftServer 2900 Series Скачать руководство пользователя страница 81

Required Tools

Installing the System in a Cabinet

9-3

Required Tools

Tools required for installing a cabinet system: 

A #2 Phillips-head screwdriver 

A flat-head screwdriver and a cage-nut insertion/extraction tool 

C A U T I O N

!

To avoid personal injury or damage to the system, two 
persons are required to install the system in a cabinet.

M I S E   E N   G A R D E

!

Pour éviter toute blessure ou dommage au système, deux 
personnes sont nécessaires pour installer une armoire.

Numbering the Vertical Rails

If the holes in the vertical rails of your cabinet are not already numbered, use a marker 
or pencil to number the middle hole of at least the following: 

The 4U in which to install each shelf unit 

The 2U in which to install each pair of PDUs, if ordered 

The 2U in which to install each storage enclosure, if ordered 

N O T E

The cabinet rails, system, and various components are 
measured in Electronic Industries Alliance (EIA) rack 
units (U). Every three holes on the EIA square-hole 
pattern on the vertical rail equals one U (1.75 in., 
4.45 cm). The holes on EIA rails are located in a repeating 
pattern of 1/2 in. (1.27 cm), 5/8 in. (1.59 cm), 5/8 in. 
(1.59 cm), as shown in 

Figure 9-2

. The middle hole of 

each U has equal spacing between it and the holes 
adjacent to it. In some cabinets, numbers on the vertical 
rails identify the middle hole of each U. 

Содержание ftServer 2900 Series





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды