manualshive.com logo in svg

Stratus ftServer 2900 Series, Планирование и руководство по установке

Поделиться
Скачать
Stratus ftServer 2900 Series Скачать руководство пользователя страница 32

Selecting a UPS Unit for ftServer Systems

2-6

Stratus ftServer 29x0, 49x0, and 69x0 Systems: Site Planning and Installation Guide

(R786)

The following figures in 

Chapter 11, “Connecting the System to Electrical Power”

, show 

how to connect a system directly to separate AC sources:

Figure 11-1

 shows how to connect rack-mounted ftServer 2900, 4900, and 6900 

systems directly to two separate AC power sources.

Figure 11-3

 shows how to connect PDUs directly to two separate power sources. 

Selecting a UPS Unit for ftServer Systems 

Stratus does not sell or service UPS units. However, Stratus has qualified UPS models 
for use with ftServer 2900, 4900, and 6900 systems. 

Use 

Table 2-1

 to determine the number of watts the A-side of your system requires, and 

then see 

http://stratadoc.stratus.com/genref/refsell/qualified_equipment.html

 to select 

an appropriate UPS model.

N O T E

Site planning information for the UPS in this document is 
of a general nature only. Do not rely exclusively on the 
UPS information in this document. Contact APC at 

http://www.apc.com

 for detailed UPS specifications, 

documentation, sizing, and ordering information.

Communicating with a UPS over a Network

Use the following additional tools to enable a UPS and an ftServer system to 
communicate over the network:

APC UPS Network Management Card 2 (APC part number AP9630)

APC PowerChute

®

 Network Shutdown for the ftServer system. (See 

http://stratadoc.stratus.com/genref/refsell/qualified_equipment.html

 for the 

PowerChute Network Shutdown (PCNS) release number.)

When you install your ftServer system, download PCNS from APC, and install and 
configure the tool on the system, as described in one of the following manuals: 

Stratus Automated Uptime Layer for Windows-based ftServer Systems: Installation 
and Configuration

(R002W) 

Stratus Automated Uptime Layer for Linux-based ftServer Systems: Installation 
and Configuration

(R013L)

Stratus Automated Uptime Layer for VMware vSphere-based ftServer Systems: 
Installation and Configuration

(R004E)

Содержание ftServer 2900 Series





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды