manualshive.com logo in svg

Stratus ftServer 2900 Series, Планирование и руководство по установке

Поделиться
Скачать
Stratus ftServer 2900 Series Скачать руководство пользователя страница 116

Connecting the System Directly to a UPS

11-4

Stratus ftServer 29x0, 49x0, and 69x0 Systems: Site Planning and Installation Guide

(R786)

power is removed. If you need assistance in planning 
and testing your UPS configuration, contact the 
Stratus Customer Assistance Center (CAC) or your 
authorized Stratus service representative.

3. For more information about qualified UPS units, see 

http://stratadoc.stratus.com/genref/refsell/qualified_e
quipment.html

.

N O T I C E

The network switch that connects the UPS to the ftServer 
system must be connected to UPS power. Otherwise, the 
UPS cannot send an OS shutdown message to the 
ftServer system if the network is down. 

1. From the front of the system, make sure that the CPU-I/O enclosures are fully 

inserted into the shelf unit by tightening the thumbscrews, if necessary.

2. Locate two black power cords and two labels, A and B.

3. Attach an A label to one power cord. 

Connect the IEC-C13 end of the cable to the receptacle on the 

top

 CPU-I/O 

enclosure. (Lift the small power-cord locking bar above the receptacle to insert the 
power cord into the enclosure.) Connect the other country-specific end
to the UPS. See 

Table 2-10

 to select the power cord that meets your configuration 

and country’s power connection requirements.

4. Attach a B label to the second power cord. 

Connect the IEC-C13 end of the cable to the receptacle on the 

bottom 

CPU-I/O 

enclosure. Connect the other end to a second, separate power source.

To configure the system to communicate with a UPS in the case of a power outage, 
see one of the following manuals:

Stratus Automated Uptime Layer for Windows-based ftServer Systems: Installation 
and Configuration

(R002W) 

Stratus Automated Uptime Layer for Linux-based ftServer Systems: Installation 
and Configuration

(R013L). 

Stratus Automated Uptime Layer for VMware vSphere-based ftServer Systems: 
Installation and Configuration

(R004E)

Содержание ftServer 2900 Series





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды