manualshive.com logo in svg

Stratus ftServer 2900 Series, Планирование и руководство по установке

Поделиться
Скачать
Stratus ftServer 2900 Series Скачать руководство пользователя страница 108

Connecting the ftServer System to External Storage Systems

10-6

Stratus ftServer 29x0, 49x0, and 69x0 Systems: Site Planning and Installation Guide

(R786)

To connect the Ethernet ports to networks

1. Connect the ports for the embedded Ethernet controllers to networks. Obtain the 

appropriate cables and connectors (see 

Table 4-4

) for each of the system Ethernet 

ports you plan to use. Connect one end of each cable to a network port on the 
system and the other end to an Ethernet wall jack or switch. Items 8 and 9 in 

Figure 10-1

 show the 1GbE and 10GbE network ports, respectively, on the 

systems.

2. If the system contains Ethernet adapters in PCI slots, connect them to a network. 

Connect the LAN adapter team to the same network subnet as the iSCSI storage 
array using two network switches for fault tolerance.

For ports on copper gigabit Ethernet adapters, use UTP cables with RJ-45 
connectors. 

N O T E S

1. If you are installing the adapters, install them in pairs, 

one in the same slot in each CPU-I/O enclosure. 

2. Add cables in pairs, a cable connected to the same 

port in the same slot in each CPU-I/O enclosure. If 
you are using a single pair of ports, attach cables to 
the top port(s) of each card and attach both cables to 
the same network. 

After you connect the cables and install the software, and when the system is running, 
configure the iSCSI software initiator and configure the Ethernet ports into 

teams

 (on 

Windows-based systems), 

channel-bond interfaces

 (on Linux-based systems), or 

vSwitches

 (on VMware vSphere-based systems). 

For information about configuring the iSCSI software initiator, see the 

ftScalable 

Storage G3: Getting Started Guide

(R687) or the links in the 

ftScalable Storage G4 

System Documentation

 section in the Preface.

For instructions about configuring Ethernet ports, see one of the following manuals: 

Stratus ftServer System Administrator’s Guide for the Windows Operating 
System

(R014W)

The 

Stratus ftServer System Administrator’s Guide for the Linux Operating 

System

(R003L)

Stratus ftServer System Administrator’s Guide for VMware vSphere

(R002E) 

Содержание ftServer 2900 Series





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды