manualshive.com logo in svg

Stratasys uPrint, Руководство по обслуживанию, Страница: 319 / 383

Поделиться
Скачать
Stratasys uPrint Скачать руководство пользователя страница 319

 

6-52

Part curling

Characteristics: Top surface appears rough. Model and support will separate or support and 
substrate will separate.

70.

Corrective actions

1.

The part is too dense, try using the “Sparse Fill” option in CatalystEX.

2.

Modeling base has been re-used or is defective. Replace with unused modeling base.

3.

Run Z Calibrations.

4.

Verify proper operation of all chamber fans. Replace fans as needed.

5.

Verify chamber heaters are secured and operating properly. Replace heaters as needed.

6.

Verify X, Y and Z level is within specification. If not level, re-level and calibrate.

Содержание uPrint
































































































































































































































































































































































































Отзывы:

Нет отзывов