Stratasys uPrint Скачать руководство пользователя страница 275

Страница: 275 / 383

6-8

Recovering from loss of extrusion

18.

Enter

Head Maintenance

mode.

From

Idle

, press

Maintenance

Press

Machine

Press

Head.

The

head will heat up to operating temperature which will take

approximately 3 minutes.

19.

20.

Remove the head cover by pressing the tabs in and pulling away from the head. See

Figure 6-380.

Figure 6-380: Remove the head cover

21.

22.

Place the toggle bar in neutral position (bar will extend equally from both sides of head).

This can be done manually - push on the extended bar end. See

Figure 6-381.

Note:

It is recommended that you read and understand this entire procedure

before performing any of the work.

Gloves:

The head area is hot. Use leather gloves when working in this area of

printer.

Press tabs in to

remove head cover

Head Cover

Содержание uPrint
































































































































































































































































































































































































Результаты поиска

Содержание uPrint

Отзывы:

Stratasys uPrint, Руководство по обслуживанию, Страница: 275 / 383

Результаты поиска

Содержание uPrint

Отзывы: