Stratasys CleanStation DT3 Скачать руководство пользователя страница 6

DT3 CleanStation

DOC-01121 Rev. A

3-6

3  Safety Guidelines

The following general guidelines, together with the instructions provided 
throughout this guide, ensure user safety while operating and maintaining the 
DT3 CleanStation. 

If the system is not operated as specified, the user's 

safety might be compromised!

•  Never operate the DT3 CleanStation while the cover is open.
•  The power cable should be connected at an easily accessible electric socket 

near the DT3 CleanStation.

•  Do not move the DT3 CleanStation so that the power cable becomes taut or 

disconnects from the power socket.

•  A VAC ground fault interrupt (RCD) must be used.
•  Only operate the DT3 CleanStation when wearing neoprene gloves, safety 

goggles and a protective mask.

•  Make sure that the room is properly ventilated. The ventilation system should 

change the air at least four times every hour.

•  Remove parts with the supplied basket or with steel or plastic tongs. Do not 

use aluminum tongs when the cleaning solution is in the DT3 CleanStation.

•  Never move the DT3 CleanStation when there is liquid in the tank.
•  Placing parts in the tank raises the liquid level. Monitor the liquid level of the 

tank to prevent overflowing.

3.1  Alkaline Cleaning Solution Safety Instructions

Wear the following protective clothing when working with the alkaline cleaning 
solution:

•  safety goggles
•  protective mask
•  nitrile gloves
•  boots or closed shoes

Depending on how you plan to handle the alkaline cleaning solution, the 
suggested protective clothing listed above might not be sufficient. Consult 
your company Safety Officer 

before 

handling the solution. 

3.1.1 

Preparing the Alkaline Cleaning Solution

Always add caustic soda to water. Never pour water onto caustic soda. Mixing it 
with water generates heat that could ignite other materials. See DOC-08380, 
"Working with Alkaline Cleaning Solution".

 

3.2  Waste Disposal

Fully cured models present no special safety or health-related issues. However, 
check if local regulations regard cured and partially cured resins as hazardous 
industrial waste, and comply with all applicable regulations governing their 
disposal.

Dispose of the alkaline cleaning solution according to local regulations.

Содержание CleanStation DT3


















Отзывы: