Stratasys CleanStation DT3 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 17

Stratasys CleanStation DT3 Скачать руководство пользователя страница 4

DT3 CleanStation

DOC-01121 Rev. A

3-4

1 Introduction

The DT3 CleanStation uses agitation and water-flow to rapidly dissolve soluble
support material from printed parts and models.

1.1 About this Guide

The information and requirements provided in this document ensure proper
installation and operation of the DT3 CleanStation. The customer is responsible
for preparing the site as described in this document. If you have any questions
about the information in this document, contact your Stratasys representative.

1.2 For More Information

For more information about Stratasys, its technologies, products, and application
methods, visit

http://www.stratasys.com

. If you have any questions about the

information presented in this document, or if you have any comments or
suggestions for future editions, please send a message to

[email protected]

.

«
...
2
3
4
5
6
...
»

Содержание CleanStation DT3


















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды