Strata CIX 200 Скачать руководство пользователя страница 327

Страница: 327 / 508

IP Telephone Programming

IP Telephone Installation and Network Connection Setup

Strata CIX Programming Vol.1 12/09

8-13

IP T

phone

Pr
ogra

mming

161 LIPU/MIPU/GIPU Configuration

Prerequisite Program:

None

This command defines the network configuration of an MIPU/LIPU/GIPU.

1. Select IP-Telephony > L/M/G IPU Configuration.

2. Select Cabinet and Card slot from list on right side, or enter a location and setup the MIPU/LIPU/GIPU

by adding values to the remaining fields.

3. Click

Submit

IELD

ESCRIPTION

00 Cabinet & Slot

Number

Enter the cabinet and slot number of the MIPU/LIPU/GIPx to be configured.

Cabinet numbers:

•

CIX/CTX100: Select 01 for Base and Expansion cabinet.

•

CIX200: Select 01 for Base and 02 for Expansion cabinet.

•

CIX/CTX670: Select 01 for Base and 02~07 respectively for each
Expansion cabinet.

•

CIX1200: Select 01 for Base and 02~12 respectively for each
Expansion cabinet.

Slot numbers:

•

CIX/CTX100: Select 01~04 for Base slots and 05~09 for Expansion
slots.

•

CIX/CTX100: Virtual Slot for ACTU Relay = Cabinet 02, Slot 05.

•

CIX200: Select 01~04 for either cabinet.

•

CIX/CTX670: Select 01~08 for Base slots and 01~10 for Expansion
slots.

•

CXI1200:Select 01~08 for Base slots and 01~10 for Expansion slots.

•

CTX28 and CIX40 assignments are hard coded and cannot be
changed.

•

Virtual Slot for GCTU Relay = Cabinet 02, Slot 05.

01, 01 - 8 digital telephones on motherboard (CTX28, CIX40 R1HW and R2HW).

01, 02 - 3 CO lines on motherboard (CTX28, CIX40 R1HW), 4 CO lines (CIX40

R2HW)

01, 03 - no card (CTX28, CIX40 R1HW), GVPH (CIX40 R2HW)

01, 04 - 1 (Base) or 2 (GSTU) analog station ports (CTX28, CIX40 R1HW and

R2HW)

01, 05 - GVMU (CTX28), GVPH (CIX40 R1HW), GIPx, MIPU or GCOCIH (CIX40

R2HW)

01, 06 - GIPx, MIPU16 or GCOCIH (CIX40 R1HW), no card (CTX28, CIX40

R2HW)

01, 07 - 8 digital telephones on GCDU (CTX28, CIX40 R1HW and R2HW).

01, 08 - 3 CO lines on GCDU (CTX28, CIX40 R1HW and R2HW).

Содержание CIX 200





























































































































































































































































































































































































































































































































Результаты поиска

Содержание CIX 200

Отзывы:

Похожие инструкции для CIX 200

Бренды по названию

Популярные бренды

Strata CIX 200, Руководство по программированию

Результаты поиска

Содержание CIX 200

Отзывы:

Похожие инструкции для CIX 200

Бренды по названию

Популярные бренды