background image

6

7

IMPORTANT SAFEGUARDS

IMPORTANT SAFEGUARDS

• 

Do not operate appliance with 

a damaged cord or plug or if 

any of the parts are damaged. 

If the supply cord is damaged, 

it must be replaced by the 

manufacturer, its service agent, 

or similarly qualified persons 

for examination, repair, or 

electrical or mechanical 

adjustment in order to avoid a 

hazard.

• 

Any other servicing should be 

performed by an authorized 

service representative.

• 

This device complies with part 

15 of the FCC Rules. Operation 

is subject to the following 

two conditions: (1)this device 

may not cause harmful 

interference,and (2)this device 

must accept any interference 

received,including interference 

that may cause undesired 

operation.

• 

Changes or modifications 

not expressly approved by 

the party responsible for 

compliance could void the 

user’s authority to operate the 

equipment.

• 

NOTE: This equipment has 

been tested and found to 

comply with the limits for a 

Class B digital device, pursuant 

to Part 15 of the FCC Rules. 

These limits are designed 

to provide reasonable 

protection against harmful 

interference in a residential 

installation. This equipment 

generates, uses and can 

radiate radio frequency 

energy and, if not installed 

and used in accordance with 

the instructions, may cause 

harmful interference to radio 

communications. However, 

there is no guarantee that 

interference will not occur 

in a particular installation. If 

this equipment does cause 

harmful interference to radio 

or television reception, which 

can be determined by turning 

the equipment off and on, 

the user is encouraged to try 

to correct the interference by 

one or more of the following 

measures: 

 

• 

Reorient or relocate the 

receiving antenna.

• 

Increase the separation 

between the equipment and 

receiver.

• 

Connect the equipment into 

an outlet on a circuit different 

from that to which the receiver 

is connected.

• 

Consult the dealer or an 

experienced radio/TV 

technician for help.

PLEASE READ AND SAVE THIS 

INSTRUCTION AND CARE MANUAL

Содержание PancakeBot PNKB01
















Отзывы: