Stoelting VB25 Freezer Скачать руководство пользователя страница 6

English

Vertical batch freezer

6

The technical data plate and CE marking must not be removed.  It is placed on the back side of the device and identifies:

-

the name and address of the manufacturer [1];

-

the designation of the model [2];

-

the relative serial number [3] and the year of construction [4];

-

the values of voltage and frequency [5];

-

the type of cooling [6],  the power [7] and current [8] consumption;

-

the type and quantity of freezing gas contained [9];

-

the values of high and low pressure [10] and the CE marking [11].

3.2

Acoustic pressure level

The average equivalent continuous acoustic pressure level of this machine is quoted in the Technical Handbook (Technical
Data section).  This data has been measured at 1 meter from the surface of the machine and at 1. 60 meters from ground-
level,  during the machine’s functioning.

4

C

ARRYING AND UNPACKING

Note:

We suggest you to let the Assistance Service or qualified technicians carry out the transportation, un-
packing and installation.

T

O LIFT THE MACHINE ALWAYS USE AN ADEQUATE

LIFTING DEVICE

.A

TTEMPTING TO LIFT IT MANUALLY

IT

'

S DANGEROUS AND IT CAN DAMAGE YOUR HEALTH

.

The machine’s weight specifications,  both including packing and net,  can be found in
both the supplied documents and on the packing itself.

To prevent the oil contained in the compressor to flow into the refrigerating circuit, it is neces-
sary to always keep the machine in upright position, during carrying, installation and operation.
Always follow the instructions on the packing.

4.1

Transport of the packing machine

The packing has been designed to assure to the machine the highest safety.

It is therefore suggested to transport the machine while it is packed as near as possible
to the place where it will be installed.

To carry the packing machine,  use an elevator,  or a bench trolley,  inserting its forks in
the basement’s holes.

4.2

Unpacking

Unpack the machine and carefully check it.  In case of doubt,  do not use it,  and call the
Seller.

-

cut the straps and remove the cardboard box from the top;

Содержание VB25 Freezer

























Отзывы: