manualshive.com logo in svg

Stober SD6 Series, Руководство пользователя

Поделиться
Скачать
Stober SD6 Series Скачать руководство пользователя страница 174

ID 442426.04

174

WE KEEP THINGS MOVING

Drive controller

9

Manual SD6

9.2.5

Quick stop

When a quick stop occurs, the drive controller brings the connected motor 

quickly to a standstill. Note that a quick stop is always performed in speed 

control and without jerk limiting.

Various signals are available to trigger a quick stop. Note the differences 

between the STOBER device state machine (for signal path see section 

9.2.5.1) and the device state machine according to CiA 402 (for signal path see 

section 9.2.5.2).

When a quick stop is triggered, the device state machine switches to the 

quick 

stop

 state. The motor is braked with the ramp set in 

I17 Quick stop 

deceleration

. Note that difference sources can write to 

I17

. For example, in the 

Controller Based Mode

, 

A578 Quick stop deceleration

 is copied to 

I17

. 

During the quick stop the torque limit 

C08 quick stop torque limit

 is in effect. 

Note that the torque set in 

C08

 can be reduced if an operating limit of the drive 

controller or motor is violated by 

C08

. Other torque limit values such as 

C03 

max-positive torque/C05

 and 

max-negative torque

 are ignored. For a detailed 

description of torque limits see section 13.6 Limit torque, force.

If the drive controller is unable to bring the motor to a standstill with ramp 

I17

 

in time 

A39 t-max. quick stop

, the motor coasts down: 

1

Reference value

2

Actual course with coasting

The 

Quick stop end

 is activated 

•

for motors without a brake when the motor has reached a standstill.

•

for motors with a brake when the brake is set (

F08 brake is closed

).

Resolution

Quick stop end

n

t

I17

Resolution

Quick stop end

n

t

2

1

A39

t=v/I17

Содержание SD6 Series
























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды