manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RS_Telecom IP

RM0082

790/844

Doc ID 018672 Rev 1

RESET: all ‘0’

34.6.9 IT-GEN 

register

This register manages pin IT[7:0] or GPIO10_in [7-0]. It allows generating an interrupt when
either a change appears on one pin, or when a change is stable for a persistency time given
by PERS_time register. The supervision is done on the global Byte and not bit per bit
(stability must be encountered on the 8 pins).

RESET: all ‘0’

Table 710.

GPIO10_in register (Offset 0x1C)

Bits

Name

Comments

[31:10]

Reserved

Latched value from the respective pins.

[09]

In9

[08]

In8

[07]

In7

[06]

In6

[05]

In5

[04]

In4

[03]

In3

[02]

In2

[01]

In1

[00]

In0

Table 711.

IT_GEN register (Offset 0x24)

Bits

Name

Comments

[31:24]

Reserved

[23]

GPIO7

GPIOx=1: GPIO10_in[x] pin is taken into account to generate 
the interrupts

GPIOx=0: IT[x] pin is tkane into account to generate the 
interrupts

[22]

GPIO6

[21]

GPIO5

[20]

GPIO4

[19]

GPIO3

[18]

GPIO2

[17]

GPIO1

[16]

GPIO0

[15]

Ch7

1 - Interrupt on change on pin 7

0 - No interrupt on change on pin 7

[14]

P7

1 - Interrupt when 8 bits are stable for pers_time after last
change on P7

0 - No interrupt on stability of change

[13]

Ch6

1 - Interrupt on change on pin 6

0 - No interrupt on change on pin 6

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

J3C S20 Assembly Instructions preview
S20
Бренд: J3C Страницы: 2
YOKOGAWA UTAdvanced UT35A Technical Information preview
UTAdvanced UT35A
Бренд: YOKOGAWA Страницы: 18
Rain Bird ESP-RZXe Installation And Operation Manual preview
ESP-RZXe
Бренд: Rain Bird Страницы: 18
PSC Solar YQPV-HP360V/100A Installation And Operating Instructions Manual preview
YQPV-HP360V/100A
Бренд: PSC Solar Страницы: 22
Bettis TEC2 Quick Start Manual preview
TEC2
Бренд: Bettis Страницы: 18
Murphy MURPHYMATIC ASM160 Installation And Operation Instructions preview
MURPHYMATIC ASM160
Бренд: Murphy Страницы: 4
Linear Technology LTC3553EPD Quick Start Manual preview
LTC3553EPD
Бренд: Linear Technology Страницы: 5
OBO Bettermann C50-0-255 Installation Instructions Manual preview
C50-0-255
Бренд: OBO Bettermann Страницы: 6
Madas RG/2MBLZ DN 80 Technical Manual preview
RG/2MBLZ DN 80
Бренд: Madas Страницы: 48
Taconova TACOTHERM FRESH PETA ES 5941S Manual preview
TACOTHERM FRESH PETA ES 5941S
Бренд: Taconova Страницы: 40
Oase InScenio Operating Instructions Manual preview
InScenio
Бренд: Oase Страницы: 646
Sensibo Sensibo Air Manual preview
Sensibo Air
Бренд: Sensibo Страницы: 15
Balmar Max Charge MC-614-H Installation And Operation Manual preview
Max Charge MC-614-H
Бренд: Balmar Страницы: 20
ZIEHL-ABEGG Acontrol PSET6 Operating Instructions Manual preview
Acontrol PSET6
Бренд: ZIEHL-ABEGG Страницы: 24
Lattice Semiconductor MachXO5T-NX Quick Start preview
MachXO5T-NX
Бренд: Lattice Semiconductor Страницы: 2
Flowserve Limitorque LTQ008 User Instructions preview
Limitorque LTQ008
Бренд: Flowserve Страницы: 41
Scaime eNod4-C BOX Manual preview
eNod4-C BOX
Бренд: Scaime Страницы: 74
Viconics VT7600F Series Installation Manual preview
VT7600F Series
Бренд: Viconics Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды