manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RS_Color liquid crystal display controller (CLCD)

RM0082

758/844

Doc ID 018672 Rev 1

         

33.6.12 LCDMIS 

register

LCDMIS is a read-only (RO) register. It is a bit-by-bit logical AND of the LCDRIS register
and the LCDIMSC register. Interrupt lines correspond to each interrupt. A logical OR of all
interrupts is provided to the system interrupt controller.

         

33.6.13 LCDICR 

register

The LCDICR is a write-only (WO) register. Writing a logic 1 to the relevant bit clears the
corresponding interrupt.

         

Table 684.

LCDRIS register bit assignments

Bit

Name

Reset 
value

Description

[13:05]

[04]

MBERROR

1’h0

AHB bus master error status. Set when the AHB
master encounters a bus error response from a
slave.

[03]

VCOMP

1’h0

Vertical compare. Set when one of the four vertical
regions, selected through the LCD control register,
is reached.

[02]

LNBU

1’h0

LCD next address base update, mode dependent,
set when the current base address registers have
been successfully updated by the next address
registers. Signifies that a new next address can be
loaded if double buffering is in use.

[01]

FUF

1’h0

FIFO underflow, set when either the upper or lower
DMA FIFOs have been read accessed hen empty
causing an underflow condition to occur.

[00]

-

-

Reserved, read as zero

Table 685.

LCDMIS register bit assignments

Bit

Name

Reset 
value

Description

[31:05]

-

-

Reserved, read as zero

[04]

MBERRORINTR

1’h0

AHB Master errors interrupt status bit.

[03]

VCOMPINTR

1’h0

Vertical compare interrupt status bit.

[02]

LNBUINTR

1’h0

LCD next base address update interrupt status bit.

[01]

FUFINTR

1’h0

FIFO underflows interrupt status bit.

[00]

-

-

Reserved, read as zero.

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

hager coviva Smartbox TKP100A Configuration Manual preview
coviva Smartbox TKP100A
Бренд: hager Страницы: 45
IAI ROBO Cylinder RCP2 Series Quick Start Manual preview
ROBO Cylinder RCP2 Series
Бренд: IAI Страницы: 5
RadioMaster MT12 Instruction Manual preview
MT12
Бренд: RadioMaster Страницы: 49
National Instruments NI 9514 User Manual preview
NI 9514
Бренд: National Instruments Страницы: 72
ABB RHD8000 Series Instructions Manual preview
RHD8000 Series
Бренд: ABB Страницы: 17
SOMFY Situo 1 RTS Installation And Operating Manual preview
Situo 1 RTS
Бренд: SOMFY Страницы: 112
Bailey infi 90 IMMFP12 Instruction preview
infi 90 IMMFP12
Бренд: Bailey Страницы: 75
YASKAWA CIMR-VC*****H**-00 series Quick Start Manual preview
CIMR-VC*****H**-00 series
Бренд: YASKAWA Страницы: 32
Cypress AN77960 Manual preview
AN77960
Бренд: Cypress Страницы: 13
M-Audio Keyboard Controller Series Quick Start Manual preview
Keyboard Controller Series
Бренд: M-Audio Страницы: 2
MAKELSAN MRG33 Series User Manual preview
MRG33 Series
Бренд: MAKELSAN Страницы: 28
Newport Pt16 Operator'S Manual preview
Pt16
Бренд: Newport Страницы: 72
Minebea Intec Maxxis 5 Original Installation Manual preview
Maxxis 5
Бренд: Minebea Intec Страницы: 138
Truma DuoControl horizontal Operating Instructions Manual preview
DuoControl horizontal
Бренд: Truma Страницы: 20
Air Torque AT1001U Maintenance Manual preview
AT1001U
Бренд: Air Torque Страницы: 11
Zamel exta life ROB-21 Instructions Manual preview
exta life ROB-21
Бренд: Zamel Страницы: 24
BFT SECURBASE LIGHT PLUS Installation And User Manual preview
SECURBASE LIGHT PLUS
Бренд: BFT Страницы: 76
YASKAWA CIMR-ZU5A Series Quick Start Manual preview
CIMR-ZU5A Series
Бренд: YASKAWA Страницы: 64

Бренды по названию

Популярные бренды

Загрузить еще бренды