manualshive.com logo in svg

STMicroelectronics SPEAr300, Справочное руководство


Поделиться
Скачать
background image

RM0082

HS_USB2.0 host

Doc ID 018672 Rev 1

447/844

22.6.29 HcInterruptEnable 

register

Each enable bit in the HcInterruptEnable register corresponds to an associated interrupt bit 
in the HcInterruptStatus register. The HcInterruptEnable register is used to control which 
events generate a hardware interrupt. When a bit is set in the HcInterruptStatus register 
AND the corresponding bit in the HcInterruptEnable register is set AND the 
MasterInterruptEnable bit is set, then a hardware interrupt is requested on the host bus.

Writing a '1' to a bit in this register sets the corresponding bit, whereas writing a '0' to a bit in 
this register leaves the corresponding bit unchanged. On read, the current value of this 
register is returned.

         

22.6.30 HcInterruptDisable 

register

Each disable bit in the HcInterruptDisable register corresponds to an associated interrupt bit 
in the HcInterruptStatus register. The HcInterruptDisable register is coupled with the

Table 370.

HcInterruptEnable register bit assignments

Bits

Name

Reset

Read/Write

Description

HCD

HC

[31]

MIE

0b

R/W

R

A ‘0’ written to this field is ignored by HC. A '1' written to 
this field enables interrupt generation due to events 
specified in the other bits of this register. This is used by 
HCD as a Master Interrupt Enable.

[30]

OC

0b

R/W

R

0 - Ignore

1 - Enable interrupt generation due to Ownership Change.

[29:07]

Reserved

[06]

RHSC

0b

R/W

R

0 - Ignore

1 - Enable interrupt generation due to Root Hub Status 
Change.

[05]

FNO

0b

R/W

R

0 - Ignore

1 - Enable interrupt generation due to Frame Number 
Overflow.

[04]

UE

0b

R/W

R

0 - Ignore

1 - Enable interrupt generation due to Unrecoverable 
Error.

[03]

RD

0b

R/W

R

0 - Ignore

1 - Enable interrupt generation due to Resume Detect.

[02]

SF

0b

R/W

R

0 - Ignore

1 - Enable interrupt generation due to Start of Frame.

[01]

WDH

0b

R/W

R

0 - Ignore

1 - Enable interrupt generation due to HcDoneHead 
Writeback.

[00]

SO

0b

R/W

R

0 - Ignore

1 - Enable interrupt generation due to Scheduling 
Overrun.

Содержание SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SPEAr300

Vacon NX series Maintenance Manual preview
NX series
Бренд: Vacon Страницы: 64
2N 9160341 Installation Manual preview
9160341
Бренд: 2N Страницы: 107
Allen-Bradley Micro850 series Installation Instructions Manual preview
Micro850 series
Бренд: Allen-Bradley Страницы: 24
Swagelok BSH 10 Series User Manual preview
BSH 10 Series
Бренд: Swagelok Страницы: 20
A & H AMFLOW A2-ACM Installation, Operation & Service Manual preview
AMFLOW A2-ACM
Бренд: A & H Страницы: 35
MegaLite MEMO CORE CONTROL User Manual preview
MEMO CORE CONTROL
Бренд: MegaLite Страницы: 11
Watts WFHC 06Z 02 HC RF 24 User Manual preview
WFHC 06Z 02 HC RF 24
Бренд: Watts Страницы: 18
Texas Instruments Errata MSP430F6779 Manual preview
Errata MSP430F6779
Бренд: Texas Instruments Страницы: 27
Midian Electronics TRC-2 Manual preview
TRC-2
Бренд: Midian Electronics Страницы: 22
Aerotech ABL9000 Series User Manual preview
ABL9000 Series
Бренд: Aerotech Страницы: 36
Savant SmartControl RS232 Quick Reference Manual preview
SmartControl RS232
Бренд: Savant Страницы: 2
Oase 33919 Operating Instructions Manual preview
33919
Бренд: Oase Страницы: 142
Aaeon TKS-G20-LN05 Manual preview
TKS-G20-LN05
Бренд: Aaeon Страницы: 54
Elan gSC2 Quick Install Manual preview
gSC2
Бренд: Elan Страницы: 2
Oki ML66592 User Manual preview
ML66592
Бренд: Oki Страницы: 466
Digital View DD-1920-DUAL-DVI Instructions Manual preview
DD-1920-DUAL-DVI
Бренд: Digital View Страницы: 30
Norgren B68 Series Installation & Maintenance Instructions preview
B68 Series
Бренд: Norgren Страницы: 2
AMD AMD-761 Software/Bios Design Manual preview
AMD-761
Бренд: AMD Страницы: 264

Бренды по названию

Популярные бренды

Загрузить еще бренды