manualshive.com logo in svg

STMicroelectronics RM0365, Справочное руководство


Поделиться
Скачать
background image

Real-time clock (RTC)

RM0365

737/1080

DocID025202 Rev 7

Caution:

To avoid losing tamper detection events, the signal used for edge detection is logically 
ANDed with the corresponding TAMPxE bit in order to detect a tamper detection event in 
case it occurs before the RTC_TAMPx pin is enabled.

•

When TAMPxTRG = 0: if the RTC_TAMPx alternate function is already high before 
tamper detection is enabled (TAMPxE bit set to 1), a tamper event is detected as soon 
as the RTC_TAMPx input is enabled, even if there was no rising edge on the 
RTC_TAMPx input after TAMPxE was set.

•

When TAMPxTRG = 1: if the RTC_TAMPx alternate function is already low before 
tamper detection is enabled, a tamper event is detected as soon as the RTC_TAMPx 
input is enabled (even if there was no falling edge on the RTC_TAMPx input after 
TAMPxE was set.

After a tamper event has been detected and cleared, the RTC_TAMPx alternate function 
should be disabled and then re-enabled (TAMPxE set to 1) before re-programming the 
backup registers (RTC_BKPxR). This prevents the application from writing to the backup 
registers while the RTC_TAMPx input value still indicates a tamper detection. This is 
equivalent to a level detection on the RTC_TAMPx alternate function input.

Note:

Tamper detection is still active when V

DD

 power is switched off. To avoid unwanted resetting 

of the backup registers, the pin to which the RTC_TAMPx alternate function is mapped 
should be externally tied to the correct level.

Level detection with filtering on RTC_TAMPx inputs

Level detection with filtering is performed by setting TAMPFLT to a non-zero value. A tamper 
detection event is generated when either 2, 4, or 8 (depending on TAMPFLT) consecutive 
samples are observed at the level designated by the TAMPxTRG bits.

The RTC_TAMPx inputs are precharged through the I/O internal pull-up resistance before 
its state is sampled, unless disabled by setting TAMPPUDIS to 1,The duration of the 
precharge is determined by the TAMPPRCH bits, allowing for larger capacitances on the 
RTC_TAMPx inputs.

The trade-off between tamper detection latency and power consumption through the pull-up 
can be optimized by using TAMPFREQ to determine the frequency of the sampling for level 
detection. 

Note:

Refer to the datasheets for the electrical characteristics of the pull-up resistors.

27.3.15  Calibration clock output

When the COE bit is set to 1 in the RTC_CR register, a reference clock is provided on the 
RTC_CALIB device output. 

If the COSEL bit in the RTC_CR register is reset and PREDIV_A = 0x7F, the RTC_CALIB 
frequency is f

RTCCLK

/64

. This corresponds to a calibration output at 512 Hz for an RTCCLK 

frequency at 32.768 kHz. The RTC_CALIB duty cycle is irregular: there is a light jitter on 
falling edges. It is therefore recommended to use rising edges.

When COSEL is set and “P1” is a non-zero multiple of 256 (i.e: PREDIV_S[7:0] = 
0xFF), the RTC_CALIB frequency is f

RTCCLK

/(256 * (P1)). This corresponds to a 

calibration output at 1 Hz for prescaler default values (PREDIV_A = Ox7F, PREDIV_S = 
0xFF), with an RTCCLK frequency at 32.768 kHz. The 1 Hz output is affected when a shift 
operation is on going and may toggle during the shift operation (SHPF=1).

Содержание RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RM0365

D-Link Express EtherNetwork DFE-670TXD Quick Install Manual preview
Express EtherNetwork DFE-670TXD
Бренд: D-Link Страницы: 4
DAD DSX 26 User Manual preview
DSX 26
Бренд: DAD Страницы: 36
D-Link DUB-1320 Quick Install Manual preview
DUB-1320
Бренд: D-Link Страницы: 2
Ebyte E43-900T13S3 Manual preview
E43-900T13S3
Бренд: Ebyte Страницы: 8
IBM LS42 - BladeCenter - 7902 Installation Manual preview
LS42 - BladeCenter - 7902
Бренд: IBM Страницы: 56
IBM ATA 133 Quick Hardware Setup Manual preview
ATA 133
Бренд: IBM Страницы: 2
IBM BladeCenter Management Module User Manual preview
BladeCenter Management Module
Бренд: IBM Страницы: 78
IBM 9040-MR9 Manual preview
9040-MR9
Бренд: IBM Страницы: 110
IBM Remote Supervisor Adapter II User Manual preview
Remote Supervisor Adapter II
Бренд: IBM Страницы: 132
XMOS xCORE-200 Multi-channel Audio board Design Manual preview
xCORE-200 Multi-channel Audio board
Бренд: XMOS Страницы: 112
3Com OfficeConnect WX2200 User Manual preview
OfficeConnect WX2200
Бренд: 3Com Страницы: 204
Quantum LightSpeed Appliance QLS250 Owner'S Manual preview
LightSpeed Appliance QLS250
Бренд: Quantum Страницы: 12
Ubiquiti U5-24-500W Quick Start Manual preview
U5-24-500W
Бренд: Ubiquiti Страницы: 23
LogLogic LX 1010 Quick Start Manual preview
LX 1010
Бренд: LogLogic Страницы: 30
National Instruments NI WLS/ENET-9163 User Manual preview
NI WLS/ENET-9163
Бренд: National Instruments Страницы: 36
National Instruments FieldPoint cFP-RTD-122 Operating Instructions Manual preview
FieldPoint cFP-RTD-122
Бренд: National Instruments Страницы: 15
Caen A 1735 Technical Information Manual preview
A 1735
Бренд: Caen Страницы: 14
Pressalit Care Indivo RK1010 User And Maintenance Manual preview
Indivo RK1010
Бренд: Pressalit Care Страницы: 31

Бренды по названию

Популярные бренды

Загрузить еще бренды