manualshive.com logo in svg

STMicroelectronics RM0365, Справочное руководство


Поделиться
Скачать
background image

DocID025202 Rev 7

288/1080

RM0365

Analog-to-digital converters (ADC)

392

15.2 

ADC main features

•

High-performance features
–

STM32F302xB/C/D/E devices have two ADCs which can operate in dual mode.

–

STM32F302x6/x8 devices have one ADC
The table below summarizes the different external channels available per ADC.

–

12, 10, 8 or 6-bit configurable resolution

–

ADC conversion time: 
Fast channels: 0.19 µs for 12-bit resolution (5.1 Ms/s)
Slow channels: 0.21 µs for 12-bit resolution (4.8 Ms/s)

–

ADC conversion time is independent from the AHB bus clock frequency

–

Faster conversion time by lowering resolution: 0.16 µs for 10-bit resolution

–

Can manage Single-ended or differential inputs (programmable per channels)

–

AHB slave bus interface to allow fast data handling

–

Self-calibration

–

Channel-wise programmable sampling time

–

Up to four injected channels (analog inputs assignment to regular or injected 
channels is fully configurable)

–

Hardware assistant to prepare the context of the injected channels to allow fast 
context switching

–

Data alignment with in-built data coherency

–

Data can be managed by GP-DMA for regular channel conversions

–

4 dedicated data registers for the injected channels

•

Low-power features
–

Speed adaptive low-power mode to reduce ADC consumption when operating at 
low frequency

–

Allows slow bus frequency application while keeping optimum ADC performance 
(0.19 µs conversion time for fast channels can be kept whatever the AHB bus 
clock frequency)

–

Provides automatic control to avoid ADC overrun in low AHB bus clock frequency 
application (auto-delayed mode) 

•

In addition, there are  internal dedicated channels available per ADC. See the table 
below:

Table 81. ADC external channels mapping

Device

ADC1

ADC2

STM32F302x6/8

15

 N.A

STM32F302xB/C

10

12

STM32F302xD/E

11

13

Содержание RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RM0365

Idis DR-8416 Operation Manual preview
DR-8416
Бренд: Idis Страницы: 123
Idis DR-6232H Installation Manual preview
DR-6232H
Бренд: Idis Страницы: 29
Idis DR-4516P Installation Manual preview
DR-4516P
Бренд: Idis Страницы: 28
Idis DirectIP DR-1304P Operation Manual preview
DirectIP DR-1304P
Бренд: Idis Страницы: 82
Idis DR-4100P Series Installation Manual preview
DR-4100P Series
Бренд: Idis Страницы: 30
Lantronix Device Server UDS 10 Hardware Manual preview
Device Server UDS 10
Бренд: Lantronix Страницы: 8
Z3 Technology Z3-DM8168-PCI-RPS Manual preview
Z3-DM8168-PCI-RPS
Бренд: Z3 Technology Страницы: 20
Z3 Technology Z3-DM8107-SDI2-RPS User Manual preview
Z3-DM8107-SDI2-RPS
Бренд: Z3 Technology Страницы: 75
Z-Wave USB Dongle User Manual preview
USB Dongle
Бренд: Z-Wave Страницы: 13
Zenith Data Systems Z-100 Series Installation Manual preview
Z-100 Series
Бренд: Zenith Data Systems Страницы: 64
NXP Semiconductors MIMXRT1160 Hardware Development Manual preview
MIMXRT1160
Бренд: NXP Semiconductors Страницы: 24
iWave iW-RainboW-G30D Hardware User'S Manual preview
iW-RainboW-G30D
Бренд: iWave Страницы: 89
MiLAN E-MCC-1600 Install Manual preview
E-MCC-1600
Бренд: MiLAN Страницы: 1
Symantec PacketShaper PS-S200 Quick Start Manual preview
PacketShaper PS-S200
Бренд: Symantec Страницы: 2
IAR SYSTEMS IAR KickStart Kit TWR-K60N512-IAR Getting Started Manual preview
IAR KickStart Kit TWR-K60N512-IAR
Бренд: IAR SYSTEMS Страницы: 8
protech ProX-1695 User Manual preview
ProX-1695
Бренд: protech Страницы: 95
QNAP TS-1283XU-RP User Manual preview
TS-1283XU-RP
Бренд: QNAP Страницы: 54
Omron NJ501-1300 User Manual preview
NJ501-1300
Бренд: Omron Страницы: 432

Бренды по названию

Популярные бренды

Загрузить еще бренды